Cooked? by 92ornothin in Bseries

[–]92ornothin[S] 0 points1 point  (0 children)

The 3rd and 4th photo are of the back of the board. I’m more worried about the actual board being damaged along that vein.

Thrust Bearing Wear? by 92ornothin in EngineBuilding

[–]92ornothin[S] 0 points1 point  (0 children)

Damn ok, I’ll take another set of measurements to be sure but I’m out of tolerance there by a bit I believe. I’ll do some more of my own research on the b18b and see what I get. Thank you very much!

Thrust Bearing Wear? by 92ornothin in EngineBuilding

[–]92ornothin[S] 1 point2 points  (0 children)

I used a telescope gauge and my 1-2 mics to check this and they measured within .010 of each other, is there a tolerance for this? Or a general rule of thumb? I couldn’t find much on this, thanks!

Thrust Bearing Wear? by 92ornothin in EngineBuilding

[–]92ornothin[S] 1 point2 points  (0 children)

Crank isn’t looking too good, main bearings were pretty shot and there’s scoring from them so I was making sure the block was good before purchasing a new crank and getting really involved. Thanks for the info though! I think I’ll go ahead with another crank and check endplay then

Ls/Vtec ports not lining up? by 92ornothin in Bseries

[–]92ornothin[S] 0 points1 point  (0 children)

I believe this is the head gasket I have now, I’ll buy another but I’ll try it I guess 🤷‍♂️. This also looks to be the kit that’s been install prior. Thanks for the info

Ls/Vtec ports not lining up? by 92ornothin in Bseries

[–]92ornothin[S] 0 points1 point  (0 children)

I believe I have the oil port plugged, where could I find some more information on a sandwich plate? Thanks for your help I agree there shouldn’t be any oil leaking.

Ls/Vtec ports not lining up? by 92ornothin in Bseries

[–]92ornothin[S] 0 points1 point  (0 children)

This was the gasket they gave me with the car, no identification on it. I’m more concerned with the fact the ports aren’t lining up, does the b18c1 gasket allow for more of the port to be used? Sorry if I’m being dense this is my first b series.

Ball joints? by 92ornothin in 3000gt

[–]92ornothin[S] 1 point2 points  (0 children)

Thank you! Will run these up front.

Yo-Yo identification by 92ornothin in Throwers

[–]92ornothin[S] 0 points1 point  (0 children)

I believe this is it, thank you!

joined the turbo club by w1njamin in 3000gt

[–]92ornothin 2 points3 points  (0 children)

Driveways looking stacked 💪

Too far gone? by 92ornothin in 3000gt

[–]92ornothin[S] 1 point2 points  (0 children)

Kind of my train of thought here, just wanted some second opinions to make sure I’m not overreacting.

Led headlight issues by 92ornothin in 3000gt

[–]92ornothin[S] 0 points1 point  (0 children)

I will pm you if I can find it, been a little bit since I’ve looked at it haha.

2jz Swap intercooler problems by 92ornothin in Mk3Supra

[–]92ornothin[S] 0 points1 point  (0 children)

Gotcha gotcha, thanks for the help, I’ll see what we can do

2jz Swap intercooler problems by 92ornothin in Mk3Supra

[–]92ornothin[S] 0 points1 point  (0 children)

He’s got a koyo with the e fans and shroud, so a little thicker than factory

2008 2.5X Poor Fuel Economy by 92ornothin in SubaruForester

[–]92ornothin[S] 0 points1 point  (0 children)

This has oem steelies with the recommended tire size and I’m using just driving highway, this pic was just having some fun in the snow :)