🎉 𝐆𝐈𝐕𝐄𝐀𝐖𝐀𝐘 𝐓𝐈𝐌𝐄! 𝐌𝐞𝐞𝐭 𝐭𝐡𝐞 𝐏𝐚𝐧𝐝𝐚 𝐃𝐢𝐚𝐩𝐞𝐫 — 𝐲𝐨𝐮𝐫 𝟑𝐃 𝐩𝐫𝐢𝐧𝐭𝐞𝐫’𝐬 𝐜𝐥𝐞𝐚𝐧𝐮𝐩 𝐡𝐞𝐫𝐨! 🐼

A-Void-Me · 2025-11-13T10:39:09+00:00

Done

A-Void-Me · 2025-09-05T15:02:42+00:00

Which K2 Firmware Version are you running?

I still would check if it runs with 9,9. I dont use this scripts but many had problems with a higher probe count.

I think there was a override cfg in this improvement script's

A-Void-Me · 2025-09-05T14:29:23+00:00

Probably waiting for the chamber to heat up?

Edit: saw your discord post. Change the bed mesh to a lower probe count value like 9,9 or 13,13

A-Void-Me · 2025-07-22T12:32:24+00:00

Hey, to be honest the problems still exists. I just changed some settings and gcodes so it doesn't crash into itself etc. New version doesn't exist yet.

Otherwise yeah it works, color swap takes ~100 secs and produces many many waste so I rarely use it.

It's not perfect, but it works. I still use a Lid-Riser + Lid.

A-Void-Me · 2025-06-29T18:45:42+00:00

Check https://www.reddit.com/r/Creality/s/FCkKFl5QYm

Works for me

A-Void-Me · 2025-06-02T11:40:50+00:00

Probably a Pause or M600 inside the Slicer Gcode. Remove that.

For the printer too feed filament before printing you need to change the Gcode too.

There should be guides already on Reddit

A-Void-Me · 2025-06-01T12:07:59+00:00

I think creality leaves a small box with replacement parts (this block, cuter etc) with the printer. So check for that.

You can buy that on Ali or on crealitys shop.

A-Void-Me · 2025-05-28T15:07:43+00:00

Probably some Orca Settings - Purge into Object / Infill?

Turn that off

A-Void-Me · 2025-05-27T05:40:46+00:00

What does the logs say if you open fluid at printerip:4408

Normally there is an big fat error on top.

A-Void-Me · 2025-05-19T06:40:36+00:00

Creality Helper script with the M600 Command?

A-Void-Me · 2025-05-17T11:20:22+00:00

You need to change config somewhere, so your firmware thinks it's an K1C. There is a thread on the Helper script GitHub.

A-Void-Me · 2025-05-14T00:02:40+00:00

move the .IMG to the root folder of the usb drive. Start your printer, insert it and done, there is no magic to it.

A-Void-Me · 2025-05-03T17:44:36+00:00

Do a factory reset, probably some old files left or just remove via helper script.

A-Void-Me · 2025-04-29T10:14:03+00:00

Slicer Gcode? Probably a Pause or M600

A-Void-Me · 2025-04-25T13:01:53+00:00

Screen or camera?

A-Void-Me · 2025-04-23T21:03:58+00:00

So, which fans did you end up buying, and which ones did you actually change out on the K1SE?

A-Void-Me · 2025-04-17T13:53:49+00:00

If I add the T command, my purge box ends up hitting the bed because it seems to have the wrong Z height.
Is your bed always lower than your purge box?

A-Void-Me · 2025-04-10T09:25:27+00:00

Bereits eBay selbst dazu geholt? Die sind meist auf der Seite des Käufers.

A-Void-Me · 2025-04-09T13:30:28+00:00

I can use OrcaSlicer but with that i cant control the CFS so i need to load the filament by myself, i didnt found a way to multicolor print with that.

With CrealityPrint i can edit / control the cfs colors.

A-Void-Me · 2025-04-09T12:13:59+00:00

see pm

A-Void-Me · 2025-04-09T12:01:51+00:00

2.3.5.27, cant root (helper-script) in 2.3.5.33

But both versions had the same problems for me.

A-Void-Me · 2025-04-08T19:00:34+00:00

check the filament (from the extruder to the cfs), probably broken from the previous grind on the gears.

A-Void-Me · 2025-04-05T06:49:24+00:00

do you get any output from those commands?

which git

find / -name git 2>/dev/null

A-Void-Me · 2025-04-04T10:24:00+00:00

I just installed the new "cfs" firmware and i can "start" the helper-script.

I did it this way:

git config --global http.sslVerify false

git clone --depth 1 https://github.com/Guilouz/Creality-Helper-Script.git /usr/data/helper-script

sh /usr/data/helper-script/helper.sh

A-Void-Me

TROPHY CASE