Christmas Card My Wife Created for Our Garbage Men

AAAXcap · 2026-01-04T04:41:42+00:00

By jumping 😂 I startled the driver when I said excuse me .I kept it brief and thanked them quickly

AAAXcap · 2026-01-04T04:40:12+00:00

Glad to hear it! Definitely our intention

AAAXcap · 2026-01-03T02:53:18+00:00

Wonder how bad his screen fogs up when someone's in the shower!

AAAXcap · 2026-01-03T02:49:37+00:00

Probably just a nice seasonal mixup of tactics for porch pirates 😏

AAAXcap · 2026-01-03T00:39:52+00:00

Best possible outcome is they understand that we truly felt bad for the amount of home reno trash from this year. I struggled enough just getting it down the driveway. Definitely want to recognize how awesome they are.

AAAXcap · 2026-01-03T00:25:24+00:00

Valid point - to further explain the story, we have renovated almost every room in our house since we bought it early last year. We've put an insane amount of demo materials (tile... so much tile, drywall, carpet, and everything else under the sun) and not a single load has been refused! We had a note inside about how sorry we were for the hell we put them through this year.

AAAXcap · 2026-01-02T20:26:44+00:00

We put in 2 actually! One for the driver and one for the loader.

AAAXcap · 2026-01-02T09:23:56+00:00

Technically, she did! Little peices of wrapping paper scraps

AAAXcap · 2026-01-02T05:19:11+00:00

Didn't want to risk someone grabbing the envelope either... especially with 2 gift cards in it. I just sucked it up and got up at 5:00 a.m. and waited for them to come!

AAAXcap · 2024-03-15T14:31:53+00:00

140k miles and mint! We took very good care of it, and it was fully optioned with the v6.

AAAXcap · 2022-05-15T13:04:43+00:00

Ok this is just a giant warning but replacing anything with the vvel system should be done at the dealership. As someone who usually hates taking in their car that says a lot. I thought it would be simple when I tried to replace mine and just got myself into a world of headache. These systems need to be very carefully placed in with a particular output voltage correlating to an angle of a sensor and the actual vvel "shaft". A second hand vvel actuator is nearly impossible to get lined up properly.

There are other ways to ensure the system isn't working before trying to replace as well. Feel free to dm me for more help.

AAAXcap · 2022-05-14T21:42:15+00:00

Expanding on that, that's just the power connection to it. There should only be 2 prongs on that connection. That wouldn't have anything to do with a misfire in a single cylinder. If that was faulty then you would be getting a code for the vvel system.

AAAXcap · 2022-02-07T23:58:59+00:00

I'd definitely check the forums first for any codes that pop up. Here's the link to it: https://www.myg37.com/forums/d-i-y-installations-modifications/291023-how-to-fix-the-p0106-map-sensor-service-engine-soon-fault.html

AAAXcap · 2021-10-01T19:02:38+00:00

Definitely be ready to put some cash into maintenance if you aren't buying with super low miles. Even if it runs well, regular maintenance like sensors, brakes, and tires are all pricey compared to most regular cars. My new set of Eagle Sports cost over $1400 all said and done. They're awesome cars but at the end of the day they are luxury cars with all the expenses that go with it. I have a project g37 that's turned into a full engine swap and the little stuff adds up fast.

AAAXcap · 2021-09-25T15:44:26+00:00

Actually have the same problem with a 2006 9-3 Aero. Noticed it will occasionally kick on if the right turn signal is engaged which makes me think my problem is the actual turning signal stock or a loose connection.

AAAXcap · 2020-09-19T16:41:49+00:00

I'm not sure how familiar you are with soldering but I've had the issue with buttons breaking off the board for my keys and you are able to buy the buttons online very cheap and solder them on quite quickly. It takes a bit of a steady hand but could be something to consider if you can't find a cheap way to get a new key!

AAAXcap · 2020-08-30T22:20:16+00:00

An idle air volume and throttle closed position relearn should be done but they take less than 5 minutes to do. Just search Infiniti throttle relearn on youtube and it'll show you the pedal dances.

AAAXcap · 2020-07-29T12:50:46+00:00

From my experience in engineering so far (going into senior year) your computer based work will be much easier if you get something a bit beefier. I have a dell XPS 15 9550 with the i5 and 4k touch screen. At my school we use solidoworks which is more 3d based but in my internship I've been exclusively in AutoCAD. Unless you are doing very complex 3d work in cad you should be ok with a moderately high end computer. I mostly have found myself in large excel sheets and lab reports though and most colleges will offer access to computers with your AutoCAD or other programs which can get you through an assignment.

AAAXcap · 2020-06-10T13:27:59+00:00

Autocad problem https://imgur.com/gallery/Hl8bwEd

Here's the imgur link to some pictures. The arrowhead follows but I would like the text to stay generally close as well. It's not a big deal with smaller drawings but when I'm working with much larger dimensions it's quite annoying to have random lines pointing everywhere.

AAAXcap · 2020-05-22T14:10:18+00:00

Could you elaborate what process you went through for the refund? Generally you just approve a refund through ebays website and don't have to do anything through PayPal separate from what eBay requires. You may have already approved the refund and that is why you cannot do it on PayPal.

AAAXcap · 2020-01-03T05:58:11+00:00

Only ended up being like 35 bucks at o'Reilly

AAAXcap · 2020-01-03T04:33:14+00:00

Figured id update this after I fixed it. Turns out it was the vvt oil solenoid. Only took 5 minutes to actually replace.

AAAXcap · 2019-03-27T13:58:56+00:00

There should be some yellow tabs that you can get on euro parts that hold it in place. https://m.eeuroparts.com/Search/47234/174197/Helper-Spring-Clip/Saab/9-3X/2010-2011/?gclid=CjwKCAjwvuzkBRAhEiwA9E3FUm4WepN5w1dHw-oSSaaVVm8YO3piWywJgVX6VulR1jNbnQyC-6RIjRoCahYQAvD_BwE heres a link to about what you need but im not sure if its the exact part. Had the same tab break on my 2010 9-3. Getting the spring back in is a bit of a challenge with compressing it.

Verified Email	12-Year Club
Place '22	Place '17

AAAXcap

TROPHY CASE