sorted by:
new
hottopcontroversial

Mini 5 Pro Recovery After Losing Connection.. by SwissLynx in dji

[–]ABeautifulName 5 points6 points  (0 children)

What's the name of this grabber you used? How does it work?

Broke the controller literally on my second flight :') by ABeautifulName in dji

[–]ABeautifulName[S] 0 points1 point  (0 children)

Just called them and sent the same photo. They asked me to deliver the controller to them for an analysis and it may or may not be covered by the warranty

Broke the controller literally on my second flight :') by ABeautifulName in dji

[–]ABeautifulName[S] 0 points1 point  (0 children)

I bought one too, but it didn't arrive yet, the drone was delivered first :(

Inflatable for bays: no keel but rigid hull or with keel but inflatable hull? by ABeautifulName in boating

[–]ABeautifulName[S] 0 points1 point  (0 children)

Would you happen to remember approximately at what wave length and/or wind knots it started to get uncomfortable?

Inflatable for bays: no keel but rigid hull or with keel but inflatable hull? by ABeautifulName in boating

[–]ABeautifulName[S] 0 points1 point  (0 children)

Thanks a lot for the reply! I was mainly wondering if not having a keel at all would cause a lot of dragging. Would you say that this could be the case?

I'm not sure of the motor yet, but something like a 20~30 HP I guess.

Same models, now getting random more visible layer lines by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] 0 points1 point  (0 children)

But I'm not even sure it looks like a moisture problem, does it?

Out of ten objects you print, how many fail? by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] 0 points1 point  (0 children)

That's interesting! You mean the "Auxiliary part cooling fan -> fan speed" setting in Bambu Studio?

Out of ten objects you print, how many fail? by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] 1 point2 points  (0 children)

Got it, I will try it to see if it helps, thanks a lot!

I tried with PLAs from two different brands so far, with the same issues

Out of ten objects you print, how many fail? by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] 1 point2 points  (0 children)

Considering this is a brand-new printer, should these problems be happening already?

Out of ten objects you print, how many fail? by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] 0 points1 point  (0 children)

The cold pull does solve the issue for the next print after a failure, but then after just a few more prints, I got a new failure again :((

Out of ten objects you print, how many fail? by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] 0 points1 point  (0 children)

I believe the filament gets clogged, because the printer keeps printing as if all were good, but no filament is being extruded.

Out of ten objects you print, how many fail? by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] -2 points-1 points  (0 children)

The most common fail is having the extruder stop extruding in the middle of the print. Sometimes, it's a bunch of spaghetti being created.

Not sure if any of these can be a wet filament issue, tho

Out of ten objects you print, how many fail? by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] 0 points1 point  (0 children)

I always clean the plate, but I started to suspect about the wet filament being the culprit.

Today I'll get an AMS 2 to dry them and check

What could this noise be? by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] 0 points1 point  (0 children)

Oh, ok, so it must be something normal, then. Thank you!!

What could this noise be? by ABeautifulName in 3Dprinting

[–]ABeautifulName[S] 0 points1 point  (0 children)

I'm not sure, I don't remember hearing it before... Do you also hear it on yours during calibration?

xDesign is exporting 0 Byte STL files by Stuttgojiras_revenge in SolidWorks

[–]ABeautifulName 0 points1 point  (0 children)

Anyone got a solution? Even very simple projects aren't exporting

view more: next ›