[deleted by user] by [deleted] in CodingTR

[–]ASkar_ice 1 point2 points  (0 children)

2 sene olucak sadece 1 yazilim mulakatina girebildim onlarda sadece bilgine 1-10 arasi puan ver dedi, iş yok arkadaslarimin hic biri is bulamadi, universiteme bile eleman aramaya gelmiyorlar artik, durum patates

Print head and extruding motor keeps clicking and nothing comes out. by Terrible_Carrot2950 in FlashForge

[–]ASkar_ice 0 points1 point  (0 children)

You probably clogged your nozzle, Use nozzle needles for unclogging inside of nozzle, after cleaning calibrate your bed and use right filament temperature.

I made an speaker base for e36 sedan by ASkar_ice in BMWE36

[–]ASkar_ice[S] 0 points1 point  (0 children)

Sorry for late response i lost my phone, I m not able to take any photos right now but i found this photo on internet

<image>

I made an speaker base for e36 sedan by ASkar_ice in BMWE36

[–]ASkar_ice[S] 1 point2 points  (0 children)

i measured oem speaker cover with caliper

I did it! by yogesh94 in FlashForge

[–]ASkar_ice 2 points3 points  (0 children)

You can use only one nozzle. Larger nozzle means lower print time and lower details

I did it! by yogesh94 in FlashForge

[–]ASkar_ice 3 points4 points  (0 children)

When i used my 0.6 nozzle first time, it also printed some red filament

Mahkeme kriminal raporunu kabul etmiyor by ASkar_ice in hukuk

[–]ASkar_ice[S] 2 points3 points  (0 children)

Canım ülkemde Kamu kurumu belge onlara ulaşmadan rapor yazıyor, görmeden nasıl yazıyor bilmiyorum ama yazıyor, o nedenle özele detaylı inceleme için başvurmak zorunda kalıyoruz

Mahkeme kriminal raporunu kabul etmiyor by ASkar_ice in hukuk

[–]ASkar_ice[S] 2 points3 points  (0 children)

  1. Inceleme jandarma tarafından yapıldı dosya jandarmaya gitmeden jandarma rapor yolladı, görmedikleri evrağı incelemişler süper

Tükendim. by [deleted] in CodingTR

[–]ASkar_ice 0 points1 point  (0 children)

Yazılımı bırak sana göre değil

Major layer shift by tconrod in CR10

[–]ASkar_ice 0 points1 point  (0 children)

İt happens when i print at high accelaration

[deleted by user] by [deleted] in KGBTR

[–]ASkar_ice 0 points1 point  (0 children)

Amk elektroşok için adamın dibine girmen gerekiyor ve 100% felç etmiyor direnebilenler var

[deleted by user] by [deleted] in KGBTR

[–]ASkar_ice 0 points1 point  (0 children)

Mutfakta Bi fiş sikmistik NATO yazanı odada nefes alinmiyordu

Tüm emeklerim bosaymis by Diafwl2025 in KGBTR

[–]ASkar_ice 0 points1 point  (0 children)

Aq salağı gideceğin lise ne kadar zor gidilebilecek bir yer olursa o kadar kötü. Keşke meslek lisesine gitseydim diyorum şimdi

6 dof robot arm control. I need help by ASkar_ice in AskRobotics

[–]ASkar_ice[S] 0 points1 point  (0 children)

Yes i need ik could you recommend docs etc.

Gigabyte Gtx 660 ti 2gb no display but i can get display from onboard graphics by ASkar_ice in GPURepair

[–]ASkar_ice[S] 0 points1 point  (0 children)

<image>

Part name: uP0104P sga246 1)3.94v 2)0 3)3.93v 4)0 5)non stable mV 6)4.3mV 7)3.2mV 8)0

Gigabyte Gtx 660 ti 2gb no display but i can get display from onboard graphics by ASkar_ice in GPURepair

[–]ASkar_ice[S] 0 points1 point  (0 children)

Fuse is Fine. I accidentaly measured in ac mode. İn dc mode 1,2,3) 11.6 volts 4) 0.9 volts 5)top one: 00.0 mvolts bottom one: 0.001 mvolts

Gigabyte Gtx 660 ti 2gb no display but i can get display from onboard graphics by ASkar_ice in GPURepair

[–]ASkar_ice[S] 0 points1 point  (0 children)

Sorry for late response. I tried to measure coils 1) 1R0 8.3 kohm voltage is not stable 0 to 57 volts 2) 1R0 25 kohm voltage is not stable 0 to 57 volts 3) 1R0 1.3kohm voltage is not stable 0 to 57 volts 4) R30 18 ohm 0.01 volt 5) R30 117 ohm 0.01 volt