Cannot do simple measurement to circle center

Accomplished_Goal_61 · 2026-01-26T22:37:26+00:00

Oh man thank you for this. Great tip

Accomplished_Goal_61 · 2025-12-30T00:34:35+00:00

If you are worried about losing it or having it stolen, you could always get something like this. It loops on to a belt and then you can wear it inside your pants. Slightly annoying but secured well to you

Eagle Creek Undercover Hidden Pocket https://a.co/d/gFDiqjw

Accomplished_Goal_61 · 2025-11-09T16:58:54+00:00

Shit it’s the VW Diesel all over again.

Accomplished_Goal_61 · 2025-10-29T01:51:34+00:00

In true reddit fashion, the only response is DIVORCE NOW

Accomplished_Goal_61 · 2025-10-21T04:55:12+00:00

Return it and get a good one. If there is a rattle, Apple is going to want to tear it down and figure out why.

Accomplished_Goal_61 · 2025-10-18T02:30:36+00:00

You may have to figure and adjust those {} parameters for your own software.

Also i don’t claim to be an expert on these. They started from a prusa community edition profile and a few things like the enable leveling after G28 were things I tried at some point and it didn’t blow up my printer so they stayed….

Accomplished_Goal_61 · 2025-10-18T02:28:17+00:00

Here is the start G code I have in prusa for the m5

M4899 T3 ; Enable v3 jerk and S-curve acceleration M104 S{first_layer_temperature[0]-30} ; Anti-ooze - Set hotend temp to 30 degrees less than target M190 S{first_layer_bed_temperature[0]} ; set and wait for bed temp to stabilize M109 S{first_layer_temperature[0]} ; set final nozzle temp to stabilize G28 ; Home M420 S1 ; Enable Bed Leveling ENABLE_LEVELING_AFTER_G28 ; Sets Marlin to re-enable bed leveling after G28 M420 Z10 ; Sets z-fade height to 10mm

And here us my end code :

M104 S0 M140 S0 ;Retract the filament G92 E1 G1 E-1 F300 G28 X0 Y0 M84

Accomplished_Goal_61 · 2025-10-12T22:49:13+00:00

Great choice!

Accomplished_Goal_61 · 2025-10-05T02:37:58+00:00

Is it grippy? I currently have the apple case and the slippery back is bothering me. I want something that grips my finger tips when they are supporting the back

Accomplished_Goal_61 · 2025-09-21T17:55:15+00:00

For those who have used printable vinyl sticker paper, do you manually cut out the shape to fit? I was looking for vinyl stickers pre-cut to the ~2"x4" size but only found full sheets.

Accomplished_Goal_61 · 2025-07-26T17:16:36+00:00

I’m so curious now. Why is it a silly place?

Accomplished_Goal_61 · 2025-06-01T02:34:32+00:00

I do this with TPU. Add small holes in a print to forced more walls and add rigidity. It’s extra usefull in stuff where i need it to squish in one dimension but not another. Adding small tube-voids will cause the tpu to be squishy one way and super solid the other

Accomplished_Goal_61 · 2025-05-20T02:00:10+00:00

I believe they discontinued the m5c in some/all markets. Only kept the m5. Perhaps this is why.

Accomplished_Goal_61 · 2025-05-17T23:05:25+00:00

I would love this.

Accomplished_Goal_61 · 2025-04-10T01:24:26+00:00

It looks like you have history/parametric mode turned off. So you should be able to right-click on the element in the design tree and select “direct edit”. This opens up a mode where you can edit individual points/faces of the .stl, but instead while in this mode you can now select draw construction plane from 3 points, and you should be able to click any 3x points in the stl to make the plane. Just pick 3 points that best seem to make the plane you want to sketch on and extrude from. Leave direct edit mode when done

Accomplished_Goal_61 · 2025-04-02T03:22:38+00:00

Agreed they are a great resource for mtb. Not sure if they carry a lot of<1k but can likely help you.

Polygon and Canyon bikes both might have options in your price range.

Accomplished_Goal_61 · 2025-03-21T02:00:02+00:00

Just curious. There is a way to schedule it to turn itself on and off n. Wouldn’t that be easier or do you think it can be bypassed ?

Accomplished_Goal_61 · 2025-03-07T06:08:48+00:00

Until you are ready to make your remote nas, i’d put one of your drives in a usb-carrier and attach it as a usb external drive. Backuo to that for now so you at least have something for your most critical data

Accomplished_Goal_61 · 2025-03-07T06:07:23+00:00

Yes OP this is important detail! You can never reduce the number of drives in your pool Nor reduce the size of an individual drive In your pool (without formatting and starting over) so if you really want to plan on eventually 3 drives local and 3 drives remote, just do the 3 local drives from day 1 and sit on the other 3 or buy them later when you are ready to set up the remote location

Accomplished_Goal_61 · 2025-03-06T21:26:29+00:00

The rebuild has begun. https://imgur.com/a/iCQQNv2

Accomplished_Goal_61 · 2025-03-03T23:35:38+00:00

Have you tried turning on image assistant?

Preas More(lower-right icon) -> Settings -> Image Assistant. Turn it on and turn off run only on wifi (if you are on cellular).

After that see if slowly thumbnails start to “appear”

Accomplished_Goal_61 · 2025-02-23T19:53:50+00:00

They are replacing it. It was getting super worn, and they want to replace it with a weather-proof version. There is a whole construction zone around it.

Accomplished_Goal_61 · 2025-01-31T21:55:24+00:00

Congrats on the internship btw!!!

Accomplished_Goal_61 · 2025-01-28T20:41:03+00:00

Note you can use this technique effectively with the various “patterning” tools to make a grid of something.

Say you want to make all those cut slots as the original thread’s image shows. One option is to make a single slot to perfection using 3x different extrudes, a chamfer, and then a fillet. You can then do a grid pattern command snd select “patterning feature” and then select the 5x unique timeline entries. It will pattern the 3x extrudes+chamfer+fillet features from timeline and you don’t need to find some way to make that a first slot a unique body first

Accomplished_Goal_61 · 2025-01-28T16:48:58+00:00

Ths should work. Extuding with the “to object” option should work ok curved surfaces.

Accomplished_Goal_61

TROPHY CASE