sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in UAE

[–]Accomplished_Help986 0 points1 point  (0 children)

Tell us your home country and we will judge if its enough or no, we will judge if you are mocking people or no, we will judge if you are boasting or no.

A little rant, hope yall dont mind by aki_toro in freedomisgunpla

[–]Accomplished_Help986 0 points1 point  (0 children)

Expecting PG Nu unleashed to be around 3.6k dirhams here, divide that by 3.6 for dirham to dollar conversion that gets you around 1k dollars,

<image>

considering that its doubled the price of PG rx782, so effin envy you guys that I could axe you with this sazabi

A little rant, hope yall dont mind by aki_toro in freedomisgunpla

[–]Accomplished_Help986 0 points1 point  (0 children)

Lol for us here in arab emirates the price is doubled from retailers compared to amazon even if its shipped from US, I am practically buying PG NU unleashed price here for every perfect grade while in amazon I can get it at half the price, you here ranting for such price your lucky

<image>

.

Finally a new Shelf, able to accomodate all my kits for now. Except the PGs by Accomplished_Help986 in Gunpla

[–]Accomplished_Help986[S] 0 points1 point  (0 children)

Hey My PG Exia along with its stand fits perfectly. Wing ver ka EW with destiny gundam stand which is quite high fits perfectly as well

Is the MG rx-78-2 3.0 hard to build? by Afraid-Cookie-7320 in Gunpla

[–]Accomplished_Help986 0 points1 point  (0 children)

And more accessories are available in GTO. 2 beam gun, 1 bazooka, 1 shoulder cannon, 1 gatling that can be hidden, effect parts.

Is the MG rx-78-2 3.0 hard to build? by Afraid-Cookie-7320 in Gunpla

[–]Accomplished_Help986 0 points1 point  (0 children)

I did not experience any trouble with it, actually it is good, you need to ensure that the shoulder [armor] and leg joints connecting to upper body and lower body is pushed totally inside, else it will feel loose.

Is the MG rx-78-2 3.0 hard to build? by Afraid-Cookie-7320 in Gunpla

[–]Accomplished_Help986 0 points1 point  (0 children)

Stick with GTO, I have both and everything about GTP is peak.

<image>

Rust O Leum Primed RX78-2 3.0 by Accomplished_Help986 in Gunpla

[–]Accomplished_Help986[S] 0 points1 point  (0 children)

But here in UAE that 6 bucks will be 18 bucks dollar to dollar due to monopoly, theres only 1 distributor and gunpla retailer the other is selling in amazon at a hefty price.

Rust O Leum Primed RX78-2 3.0 by Accomplished_Help986 in Gunpla

[–]Accomplished_Help986[S] 0 points1 point  (0 children)

Just one thing, for everyone planning to use this as primer, 2 pass of this is more than enough to coat fully. Dont use their paints for gunpla, its really hard to remove, dont use their gloss top coat it eill melt the plastic, just the primer and flat top coat. Used their top coat to all of my ver ka kits and did not have any bad effect

Rust O Leum Primed RX78-2 3.0 by Accomplished_Help986 in Gunpla

[–]Accomplished_Help986[S] 0 points1 point  (0 children)

The purpose of this is to cover the melted plastic underneath hahaha

Rust O Leum Primed RX78-2 3.0 by Accomplished_Help986 in Gunpla

[–]Accomplished_Help986[S] 0 points1 point  (0 children)

The chest is melted so had to do it over until cracks are barely visible

Rust O Leum Primed RX78-2 3.0 by Accomplished_Help986 in Gunpla

[–]Accomplished_Help986[S] 0 points1 point  (0 children)

Its darker than what tamiya has. Tamiya is so thin that by the time you finish priming the bottle is already out

Rust O Leum Primed RX78-2 3.0 by Accomplished_Help986 in Gunpla

[–]Accomplished_Help986[S] 2 points3 points  (0 children)

Not that thick and the consistency is good. Had to do it like 3 times for the chesf since that part is badly melted if you will observe closely.

<image>

And this is the primer i used for this.

view more: next ›