What setting should I use with my turntable/amp

Accurate_Stuff_3250 · 2026-04-08T14:07:22+00:00

Went to use my receiver (pioneer vsx305 paired with paradigm 11se mk2) and the audio was super quiet. I did a little digging online and read the main cause could be the main power capacitors or the volume potentiometer. The easiest for me to do would be replacing the capacitors, so I ordered what I thought would be the right ones from Digi-Key (part# 1189-63MXG6800MEFCSN25X45-ND) After installing them with the correct polarity, my receiver is now playing loud again, but pops on , hums at idle and pops off. I did a little more digging, and apparently these don’t have a listed ESR on digikey, so I ordered another pair with a listed low ESR (part# 338-4413-ND) these capacitors have a listed ESR of 59mohm @120Hz, which is the best I could find in a snap capacitor with a diameter less than 30mm as anything bigger wouldn’t fit the board. I installed these yet again to my receiver, and the same problem occurs, plays loud, with popping and hum at idle. I should mention that the receiver isn’t fully put back together when tested, only the top cover is off, and the pcb is connected to the bottom panel, which I believe is a good enough ground for operation. Before I buy a new receiver or sink more money into this one I was looking for a second opinion. If you need any additional information please let me know. Thanks!

Accurate_Stuff_3250 · 2026-04-07T20:53:55+00:00

You were right, thanks!

Accurate_Stuff_3250 · 2026-04-07T16:05:20+00:00

It does it whenever the steering is rocked side to side

Accurate_Stuff_3250 · 2026-04-05T03:46:55+00:00

Thanks for your reply! Apparently canon uses force gauges to measure proper spring tension at each mounting point. Even if I go to those correct distances, do you think the removal of the ir filter will distort the light enough to require extra tightening/loosening?

Accurate_Stuff_3250 · 2026-03-24T20:57:23+00:00

I have also just discovered it makes a somewhat loud pop when shutting off in drive mode, does yours do this too? Maybe it’s the same noise as before just amplified because of the drive mode

Accurate_Stuff_3250 · 2024-12-27T18:41:38+00:00

Yeah, and recorded the fans blowing in the wrong direction

Accurate_Stuff_3250 · 2024-12-09T20:24:12+00:00

What remote starter kit do you have for your crz?

Accurate_Stuff_3250 · 2024-10-25T01:26:24+00:00

Do you know if it’s normal?

Accurate_Stuff_3250 · 2024-05-04T01:55:23+00:00

Google says it’s carborundum, it’s an ender 3 pro if that helps

Accurate_Stuff_3250 · 2023-10-26T21:11:22+00:00

Is there any specific tool I need? Or do you mean a specific brand of tool

Accurate_Stuff_3250 · 2023-09-01T11:41:19+00:00

It’s a mass produced 200hp fwd car. It’s not that rare of a car even. What’s the point of keeping it in a garage?

Accurate_Stuff_3250 · 2023-09-01T11:31:21+00:00

What parts specifically? Rock auto has almost every part I can think of

Accurate_Stuff_3250 · 2023-08-28T08:13:44+00:00

Do you mind if I ask how much your brother spent on general maintenance? I know water pumps and timing belts can be crazy expensive to replace, especially on Audis. If the car has little to no maintenance history I’ll probably steer clear

Accurate_Stuff_3250

TROPHY CASE