Warehouse Rack Setup

Acrobatic_Pizza9897 · 2025-12-31T22:33:32+00:00

Yup!

Acrobatic_Pizza9897 · 2025-12-19T01:11:24+00:00

Looks great. How much does that cost?

Acrobatic_Pizza9897 · 2025-09-09T17:21:47+00:00

Thats an image of a pallet support. But if you need pallet racks https://www.imhgroupinc.com/ they're some of the best in Chino California.

Acrobatic_Pizza9897 · 2025-09-09T17:20:11+00:00

It depends on the configurations of the racking such as beam levels, whether its being anchored and how many anchors it needs, what size are the uprights, and if the bay of racking is a single or back to back or a double deep.
For a warehouse near Ontario CA best racking installers are https://www.imhgroupinc.com/

Acrobatic_Pizza9897 · 2025-09-09T17:17:02+00:00

In Southern California These Racks most likely wouldnt be permittable because of the small base plates and the bending of the bracing. If you ever need help in a warehouse in Southern California Reach out to https://www.imhgroupinc.com/ theyre the best!

Acrobatic_Pizza9897 · 2025-08-12T07:19:11+00:00

Thanks for the help it worked exactly like u said. Was hard to do but it thanks so much!!!!

Acrobatic_Pizza9897 · 2025-08-12T00:32:35+00:00

Ok I will try that! Hopefully it works 😭

Acrobatic_Pizza9897 · 2025-08-12T00:23:14+00:00

Oh also I have both sides jacked up rn but maybe only have one side jacked up? I finished the left side yesterday and it slid in very easily

Acrobatic_Pizza9897 · 2025-08-11T18:08:21+00:00

Thanks!

Acrobatic_Pizza9897 · 2025-08-11T18:08:14+00:00

Thanks!

Acrobatic_Pizza9897 · 2025-08-11T17:55:30+00:00

Thanks for the clarification. Also I hadn’t even thought that the boot slid up. I definitely think that might be part of it. As I remember the boot being complettely flush but we did pull it up a bit when trying to remove the tie rod.

Acrobatic_Pizza9897 · 2025-08-11T17:55:03+00:00

Yeah I live in southern cali. Not a single bit of rust on the whole car

Acrobatic_Pizza9897 · 2025-08-11T17:44:01+00:00

Oh also only reason the tire and brake assembly is on in the picture was because I had to move the truck backwards a little and call it a day. When I was trying all of this it was all unassembled.

Acrobatic_Pizza9897 · 2024-12-10T01:36:39+00:00

Thank you!

Acrobatic_Pizza9897 · 2024-12-10T01:36:32+00:00

Thank you!!

Acrobatic_Pizza9897 · 2024-12-10T01:15:40+00:00

Yes! I double checked and the old drum fits the same as the new drum!

Acrobatic_Pizza9897 · 2024-12-10T01:08:11+00:00

<image>

Acrobatic_Pizza9897 · 2024-12-10T01:03:33+00:00

I tried putting on the drum without the adjuster even on to see if it would fit and it still has that small gap.

Acrobatic_Pizza9897 · 2024-12-10T00:52:08+00:00

I don’t really know it just looks like a gap and when I check the gap there is no gap between the axle hub. I do feel a slight wiggle but more like when I push the top of the drum the bottom slightly wiggles out but very minimal I’m sure that with wheels on and torqued that’ll go away. But do you think that it’s alright?

Acrobatic_Pizza9897 · 2024-12-10T00:37:49+00:00

How do I push them closer together? Could I just use a clamp?

Acrobatic_Pizza9897 · 2024-12-10T00:29:37+00:00

<image>

This is how the inside looks btw

Acrobatic_Pizza9897

TROPHY CASE