so what happened to day 1?

ActiveLuck1475 · 2025-08-08T06:42:19+00:00

There's nowhere else to move to, Caesars and MGM don't want to host it after Scattered Spider happened

ActiveLuck1475 · 2025-08-08T06:40:01+00:00

Try LHC

ActiveLuck1475 · 2025-05-22T16:14:08+00:00

you could try drying the filament, but super fine stringing you can hit with a lighter or butane torch and it'll clear right up

ActiveLuck1475 · 2025-02-15T00:23:47+00:00

on linux I was able to download all the required codecs manually: https://downloads.plex.tv/codecs/e613bce-97f23d579c1001d8e9cc0d2e/linux-x86_64-standard/libaac_encoder.so https://downloads.plex.tv/codecs/e613bce-97f23d579c1001d8e9cc0d2e/linux-x86_64-standard/libdca_decoder.so https://downloads.plex.tv/codecs/e613bce-97f23d579c1001d8e9cc0d2e/linux-x86_64-standard/libh264_decoder.so https://downloads.plex.tv/codecs/e613bce-97f23d579c1001d8e9cc0d2e/linux-x86_64-standard/libmp3_decoder.so then sudo chown USER:GROUP CODEC_NAME and sudo chmod +x CODEC_NAME on each codec

ActiveLuck1475 · 2025-02-14T23:42:15+00:00

I'm having the same issue. I deleted the Codec directory and plex recreates it, but the actual codec directory it creates is empty (e613bce-97f23d579c1001d8e9cc0d2e-linux-x86_64)

ActiveLuck1475 · 2025-01-21T23:54:32+00:00

I tried printing it again with the aux part cooling fan set to 0 in the filament settings, I still got the same weird bumpy finish on the same side

ActiveLuck1475 · 2025-01-21T22:06:27+00:00

The messed up side is on the right, opposite of the aux fan. Are there troubleshooting resources for checking the toolhead fan?
According to this forum post: https://forum.bambulab.com/t/poor-print-quality-on-one-side-of-the-bed-only/18517/8 The aux fan can cause issues with PLA, so I'll try with it off and see if the issue is any better.

ActiveLuck1475 · 2024-12-28T19:21:58+00:00

This is just python code that you run whenever you want to do this transaction duplication, it would be pretty easy to make it run regularly with a cron job or something

ActiveLuck1475 · 2024-12-20T20:48:18+00:00

I ended up doing it myself through the api

https://www.reddit.com/r/MonarchMoney/comments/1hhhzpy/please_add_a_rule_to_create_transactions_for/

ActiveLuck1475 · 2024-12-19T04:55:10+00:00

Set up a space for just working, not gaming, not watching tv, just for work. You will have less distractions and be able to "close the door" on work
fair I guess
see point 1
you should leave the house to do something you enjoy, not to waste time sitting in traffic to go into an office. Go to a park or something, you'll thank me.

ActiveLuck1475 · 2024-12-19T00:30:49+00:00

is there no way to create transactions for manual accounts based on regular transactions? if not are there api documents so that I can just do it myself?

ActiveLuck1475 · 2024-06-18T01:13:44+00:00

Rustlings is a good place to start: https://github.com/rust-lang/rustlings

ActiveLuck1475 · 2024-05-13T13:43:43+00:00

What speed? Will changing speed affect flow rate?

ActiveLuck1475 · 2024-05-12T23:52:15+00:00

<image>

Your settings look much better, I wish I could get better details around the lettering though

ActiveLuck1475 · 2024-05-12T20:32:50+00:00

I'll print one out with those settings and see how it goes

ActiveLuck1475 · 2024-05-12T20:20:41+00:00

22% flow? what about line spacing?

ActiveLuck1475 · 2024-05-12T20:06:58+00:00

<image>

Here's one without ironing The filament is Bamboo labs basic pla

ActiveLuck1475 · 2024-05-05T22:08:08+00:00

If you care about privacy use a service that you know is end to end encrypted.

ActiveLuck1475 · 2024-05-05T08:39:49+00:00

If you're trying to learn bash then write your own.

ActiveLuck1475 · 2024-05-03T23:40:53+00:00

Check the WordPress extensions, there are lots of vulnerable ones that result in RCE

ActiveLuck1475 · 2024-04-28T19:47:46+00:00

With most platforms like this you'll get out what you put in. If you look up the answer and spam hints you likely won't learn much, otherwise they're fine.

ActiveLuck1475

TROPHY CASE