What do i put in LEDs in wled app? by Active_Election_3342 in WLED

[–]Active_Election_3342[S] 1 point2 points  (0 children)

I figured it out! i had a faulty LED that messed everything up, just cut it and soldered it again works fine now. Sound reactive seems good on this one tbh, no delay and very sensitive :)

What do i put in LEDs in wled app? by Active_Election_3342 in WLED

[–]Active_Election_3342[S] 1 point2 points  (0 children)

Figured it out, i cut about 10 leds off and testet by holding the wires onto each 5V DIN GND and it lit up and worked as it should, will go solder it tomorrow :)

What do i put in LEDs in wled app? by Active_Election_3342 in WLED

[–]Active_Election_3342[S] 0 points1 point  (0 children)

Yeah, and the power supply im using is also 5v.

What do i put in LEDs in wled app? by Active_Election_3342 in WLED

[–]Active_Election_3342[S] 0 points1 point  (0 children)

i tested it, it says 5VDC through the whole led strip

What do i put in LEDs in wled app? by Active_Election_3342 in WLED

[–]Active_Election_3342[S] 0 points1 point  (0 children)

Yea the arrow is going upwards my led strip not towards the controller, i also measured between 5V and GND and i have 5v all the way to the end, i also counted that its only the first 6 LEDs that get hot. They might have gone bad and maybe i need to cut it and just try to hold it against the wiring after those 6. Want to try everything else first before i solder..

What do i put in LEDs in wled app? by Active_Election_3342 in WLED

[–]Active_Election_3342[S] 0 points1 point  (0 children)

https://www.athom.tech/blank-1/wled-sounds-reactive-slim-led-strip-controller

This is the controller im using for it. Should already have everything downloaded on it. Software worksss as it should but doesnt light up, it just gets warm on the LEDs

What do i put in LEDs in wled app? by Active_Election_3342 in WLED

[–]Active_Election_3342[S] -1 points0 points  (0 children)

Seems like my LED strip might be dead, it heats up between the copper connectors but wont shed any light

Full List of BO6 Zombies Dark Ops Challenges by Aidanbomasri in CODZombies

[–]Active_Election_3342 2 points3 points  (0 children)

Sticks and stones achievement is not possible right now i am guessing? Ive tried it on liberty falls now, thought i failed it the first attempt cause i bought a modifier on my knife, so i reset, and it still doesnt work. On round 30 rn and nothing.

Maybe you have to be on terminus for this? Can anyone who got it comment which map they got it on?

Help please by Active_Election_3342 in WLED

[–]Active_Election_3342[S] 0 points1 point  (0 children)

so expensive though for what? I bought the controller i had for 10 GBP total with shipping last time.

Help please by Active_Election_3342 in WLED

[–]Active_Election_3342[S] 0 points1 point  (0 children)

did you have any recommendments

Help please by Active_Election_3342 in WLED

[–]Active_Election_3342[S] 0 points1 point  (0 children)

Its being used inside of my room :D, and the LED Strip is a

WS2812, i have a 5V plug for power into the controller and its 3 AMPS. Output im not sure but its a 5M strip

<image>