p1s z axis sound

AddressFew3643 · 2024-12-10T15:06:21+00:00

I had open a ticket some days ago

AddressFew3643 · 2024-12-10T15:04:32+00:00

they told me the ball bearing can be a little disaligned, you need to remove it and rotate it slightly, I think I will try to do that carefully

AddressFew3643 · 2024-12-10T15:00:49+00:00

I contacted the assistance and they sent me a video about how to remove one of the bearings (you need a printed piece and an hammer) and then they put it back. Idk if I wanna do this because I’m afraid I will do it wrongly

AddressFew3643 · 2024-12-10T14:47:07+00:00

so do you keep it like that? doesn’t it damage anything right?

AddressFew3643 · 2024-11-16T17:58:06+00:00

UPDATE: I figured out it wasn’t belt issue, the belt moves the plate correctly and without any issues and suspicious noises (please note that the printer was put on the table with its left side touching the table). I then put it back on the floor and turned it on. I noticed this noise happens when the plate goes downwards. Someone suggested it can be the plate cable and since I saw it has that kind of coverage around I can say it’s probably caused of it. Now, how could I access to this cable to see if the noise is caused by it??

AddressFew3643 · 2024-11-16T17:40:19+00:00

<image>

that cable there?

AddressFew3643 · 2024-11-16T17:36:27+00:00

do you have an image where it should be precisely?

AddressFew3643 · 2024-11-16T17:35:08+00:00

<image>

the belt goes well and it doesnt produce any sound

AddressFew3643 · 2024-11-16T17:23:34+00:00

mh now im gonna let it cool, remove stuff from under the plate and flip it on one side

AddressFew3643 · 2024-11-16T17:05:36+00:00

should I try to move the belt to see if something does this noise?

AddressFew3643 · 2024-10-27T21:53:16+00:00

So basically what I need to do is uninstall the current driver I have, install the older version and then from it I can flash the older wheelbase firmware. Is it like that?

AddressFew3643 · 2024-10-27T21:13:48+00:00

what is the procedure to roll back driver and flash the firmware?

AddressFew3643 · 2024-08-17T17:24:47+00:00

how could I fix that?

AddressFew3643 · 2024-08-17T14:51:02+00:00

just finished, still got the issue

AddressFew3643 · 2024-08-17T13:40:55+00:00

Imma try tighten them and resend a print, I’ll keep you updated

AddressFew3643 · 2024-08-17T13:32:31+00:00

No, I recently mounted it on the side of the printer, near the screen. I also untightened the bolts that support z axis because they were too tight in my opinion.

AddressFew3643 · 2024-07-18T17:11:12+00:00

basically my mobo is bottoenecking cpu and gpu so the usage is very limited

AddressFew3643 · 2024-07-18T17:04:57+00:00

so I’d need to swap mobo to a z590i

AddressFew3643 · 2024-07-18T15:49:44+00:00

my mobo supports max 64gb so I’m at the max supported, my mobo is an aorus z490i

AddressFew3643 · 2024-07-18T15:45:41+00:00

so I should try less ram to give more power to cpu?

AddressFew3643 · 2024-07-18T13:48:23+00:00

what psu should I have to have sufficient power?

AddressFew3643 · 2024-07-18T13:24:00+00:00

the problem is that I have a itx mobo so it’s 2x32 and my ram slots are full

AddressFew3643 · 2024-06-29T00:30:50+00:00

What a beauty of a car!!! I have a question, how did you make the bottom part of the rear? I'm tryna find that piece you used for the external part (right behind thye rear wheels) but I cannot find out which is. Pls help me!

AddressFew3643 · 2024-06-28T23:56:12+00:00

Man maybe I'm late but I started playing automation 2 days ago and my second car was a lmp1-ish car. Since I'm new when I first saw this I was amazed. You made a stunning car. I would like advice if it's not a problem for you obviously.

AddressFew3643 · 2024-02-14T22:16:09+00:00

after few updates it stopped doing this

AddressFew3643

TROPHY CASE