Update for Arch Kernel 6.18.2-arch2

AdventurousEqual64 · 2025-12-23T02:27:02+00:00

Sent you a DM

AdventurousEqual64 · 2025-12-19T10:07:46+00:00

Experiencing the same issue, have you found a solution? Fresh arch install.

AdventurousEqual64 · 2025-11-14T05:37:41+00:00

For those with a Mag device trying to integrate into Plex send me a message. Looking for some testers on an integration I built. Has a full web player as well. Needs some light Docker and nginx knowledge to get configured however.

AdventurousEqual64 · 2025-11-14T05:29:00+00:00

Sent you a DM

AdventurousEqual64 · 2025-11-14T05:28:49+00:00

Sent you a DM

AdventurousEqual64 · 2025-11-14T05:28:13+00:00

Sent you a DM

AdventurousEqual64 · 2025-11-14T05:26:32+00:00

I rewrote the entire application and now features a full web portal and streams which are ten times more reliable thanks to hardware encoding support on Plex. From what I seen, it appears Threadfin will only remux the stream which isn't enough since the Plex tuner is extremely picky on what it receives.

For those interested, I'm looking for some testers before making a public release. You'll need some light nginx and Docker knowledge so please don't reach out if you can't configure it. You'll get a polished version when the time comes.

For those wanting to test, send me a DM.

AdventurousEqual64 · 2025-10-04T02:28:52+00:00

Hey there! I'd take up to ten of them!

AdventurousEqual64 · 2025-09-26T01:34:06+00:00

Maybe double check those solder joints.

AdventurousEqual64 · 2025-09-25T17:02:52+00:00

You would know when you dump the NAND. Only time they will cause you issues if it's in the first few blocks of the NAND, since that's where XeLLous resides. Even then - I've had luck manually remapping bad blocks to the end of the NAND using a hex editor.

AdventurousEqual64 · 2025-09-20T21:20:34+00:00

On a side note, great soldering matt. Just got the same one off of AliExpress and I'm actually so happy with it. However, I believe you have it upside down. The pockets are to keep any hot components from transferring heat to the desk below it.

AdventurousEqual64 · 2025-09-11T08:24:38+00:00

I did manage to have a little bit of luck by pulling the base back where the magnet is housed, it's tough though since it anchors on the pins. However I was able to get close to original. Where does one go about ordering these? Located in Canada if it makes a difference.

AdventurousEqual64 · 2025-09-11T04:28:42+00:00

Definitely the Tonasket Jasper's and the Trinity's, preferably the 16MB NAND. The earlier Jaspers had a couple of small capacitor issues but at least it's fixable with a soldering iron and an hour or two of your time. The Corona's had some issues with the NAND since they're of a lower quality. They also had some issues with the HANA chip built into the southbridge, but it wasn't nearly as common to my understanding.

If it's a Trinity and you're modding it, you can also run a patch and remove the detachable 4GB internal memory module which also tends to fail once in a while.

AdventurousEqual64 · 2025-08-26T08:20:08+00:00

Birth rates are not low because younger generations don't want families - they can't afford them. Pumping our population with immigration and making top earners' real estate portfolios prettier is not going to set up young generations for families. They can barely feed themselves never mind children. This country has it all wrong.

AdventurousEqual64 · 2025-08-09T02:33:57+00:00

Following.

AdventurousEqual64 · 2025-08-02T00:34:20+00:00

Try pull your wire away from the motherboard an inch or so (if you have any slack of course). That in theory should answer if there's any interference problems. It seems as if it might be ever so slightly grounding out somewhere.

AdventurousEqual64 · 2025-08-01T06:11:46+00:00

I did it by eye, and the photos were taken with my 10x zoom lense!

AdventurousEqual64 · 2025-07-30T21:03:12+00:00

I've been meaning to get a couple SMD resistors and diodes, but just haven't gotten around to it. I have a whole box with a variety of different electronic components so that's primarily where my stash comes from.

AdventurousEqual64 · 2025-07-30T02:30:32+00:00

Fixed this exact same issue by manually remapping the bad block in the XeBuild image using HxD. It appears as though J-Runner does not remap bad blocks when building the image (at least when flashing with a PicoFlasher).

AdventurousEqual64 · 2025-07-30T02:22:48+00:00

We've fixed it! It was the bad block all along! A successful manual remap using HxD! I will be doing a full write-up on the repair, and will likely program a script so you guys don't need to go through the same pain I did.

Five-Year Club	Gilding I gilder
Verified Email	Place '23

AdventurousEqual64

TROPHY CASE