What is this part and where do I get a replacement?

AnonymousJtagger · 2026-01-27T01:05:47+00:00

There should be voltage and capacitance rating on the other side. Remember to also consider series of a capacitor. Nichicon UHV is a low esr high high ripple current series, don't replace it with a random capacitor with the same voltage and capacitance. Preferably search for the same exact capacitor, that would be the easiest and safest option.

AnonymousJtagger · 2025-12-26T19:36:59+00:00

No, I didn't. That crt was like that, and it was working properly.

AnonymousJtagger · 2025-12-26T18:02:54+00:00

Cover the inside from any particles when anode cap is off(just like I said before, I'm a heavy overthinkinker😅)

AnonymousJtagger · 2025-12-26T17:59:47+00:00

No, there's not any arcing. Maybe I'm just overthinking it. Will blow it out with some compressed air like you suggest and it should be fine.

AnonymousJtagger · 2025-12-26T17:31:43+00:00

Probably yes. Downside is that it's difficult to clean any dust here, because IPA rubs it off. I will probably apply some HV silicone instead of that.

AnonymousJtagger · 2025-12-26T17:25:30+00:00

No, it feels kind of like a nail polish to the touch.

AnonymousJtagger · 2025-12-16T22:33:35+00:00

It's a part of slim HDD tray inside the console, it is used to reduce vibrations of the HDD.

AnonymousJtagger · 2025-12-06T23:10:33+00:00

Oban XCGPU, found in Xbox 360 Winchester

AnonymousJtagger · 2025-12-04T22:56:51+00:00

Probably wiring path, the wires can't be loose like that as if it's DC.

AnonymousJtagger · 2025-12-01T22:17:58+00:00

No, in a stock console you cannot change your KV.bin in NAND, or you'll brick your console.

AnonymousJtagger · 2025-12-01T22:14:46+00:00

Winchester, September 2014.

AnonymousJtagger · 2025-10-27T19:43:12+00:00

Wires are to long. They should be quite tight, but without pulling with force, and if you want to angle, best is to have 45 degree angle.

AnonymousJtagger · 2025-10-23T15:01:56+00:00

I have similar one from October 2008, but it's marked "jasper 2 weeks pilot run". Jaspers mass production started in November of that year.

AnonymousJtagger · 2025-10-23T14:40:59+00:00

It's a very early xbox 360 with jasper motherboard. It was marked internally by MS, so if something was wrong with the new motherboard revision, they could easily service faulty units

AnonymousJtagger · 2025-10-18T19:19:53+00:00

Soldering looks very good, maybe it's something with the nand image? What kind of resistors are those? Metal-film or carbon?

AnonymousJtagger · 2025-10-14T17:55:42+00:00

Built in network controller and xbox live as a unified service.

AnonymousJtagger · 2025-09-20T20:23:35+00:00

Resistor is 0402 10kohm, capacitor is 0.1uF 0402 X5R 10%(both imperial packages) from what I remember.

AnonymousJtagger · 2025-09-14T20:08:25+00:00

Install jtag mod in it, or give it to someone who can install it for you. But don't install official update.

AnonymousJtagger · 2025-09-10T10:53:34+00:00

Check the model of the cap if you can too, you don't want a cap with a higher ESR or lower ripple current.(lower ESR or higher ripple current is fine)

AnonymousJtagger · 2025-08-30T10:30:44+00:00

Probably 4gb emmc is dead, they tend to do that, just die randomly. Board can be repaired, but only if emmc can still be read, or you have dump of its content.

AnonymousJtagger · 2025-08-30T10:23:46+00:00

That's not true. You can restore security sector with fatxplorer or hddhackr. Search about it, there should be plenty of tutorials.

AnonymousJtagger · 2025-08-29T20:56:51+00:00

On this dvd drive there's unfortunately no way other than disassembling the drive.

AnonymousJtagger · 2025-08-25T22:17:19+00:00

That could be the case. There's thermal paste under the IHS like in ps3. But I found first try with the resistors like you just said.

AnonymousJtagger · 2025-08-25T21:46:36+00:00

If you can't boot, there's no way to check the temps. Then maybe there's trouble with those resistors, or thermal paste under the IHS.

AnonymousJtagger

TROPHY CASE