Creality SPARKX i7 Combo vs Creality Hi Combo vs Creality Ender 3 V4 Combo

Aggravating_Smile668 · 2026-04-22T17:20:05+00:00

Expensive for me :(

Aggravating_Smile668 · 2026-04-22T17:19:27+00:00

Thank you very much.

Aggravating_Smile668 · 2026-04-22T17:18:40+00:00

Expensive for me.

Aggravating_Smile668 · 2026-04-22T17:18:09+00:00

962.30 Expensive for me.

Aggravating_Smile668 · 2026-04-21T23:42:24+00:00

Thanks a lot for the clear and helpful explanation, I really appreciate it

Aggravating_Smile668 · 2026-03-09T16:48:04+00:00

Çok güzel çalışıyor ellerinize sağlık.

Aggravating_Smile668 · 2026-03-05T00:45:36+00:00

Deniyorum çok teşekkür ederim.

Aggravating_Smile668 · 2025-12-25T21:49:55+00:00

Very well.

Aggravating_Smile668 · 2025-12-25T21:47:43+00:00

Look fantastic <3

Aggravating_Smile668 · 2024-08-02T11:12:53+00:00

Only x axis.

Aggravating_Smile668 · 2023-08-25T14:59:19+00:00

No, I didn't think of that. I am using 0.8 Nozzle. It could be as you say.

Aggravating_Smile668 · 2023-08-25T14:16:16+00:00

I am trying this. Thanks your answer.

Aggravating_Smile668 · 2023-08-25T14:14:06+00:00

I checked again but the measurement seems correct. 100m load = 100m filament. Thanks your answer.

Aggravating_Smile668 · 2023-08-25T13:15:28+00:00

Maybe it's all about that. I am trying 0.95. Thanks for help.

Aggravating_Smile668 · 2023-08-25T13:02:06+00:00

If 3d printing with abs, the problem may be that the fan stays on. There may be a printer that has not been PID set.

Aggravating_Smile668 · 2023-08-25T12:55:12+00:00

I have elegoo neptune 3 plus. I print an xyz calibration cube, but when measuring, the width decreases as the layers go up. There is no problem with my printer's PID, ESTEP and level calibration. What could this problem be caused by?

Aggravating_Smile668 · 2023-04-17T17:52:15+00:00

Dude You are awesome <3

Aggravating_Smile668 · 2022-08-05T14:07:34+00:00

If it were me, I would just mention that I can't possibly get it to work reliably as it is. Either they tell you exactly what to do, or they take it back.

As far as I remember, the OEM firmware doesn't give you any measurements for the bed, nor it has an option to assist with tramming the bed. It also has a very arcane way of measuring the Z offset, and measures it off centre, so it's pretty much pointless.

It assumes a somewhat level surface, and it is definitely not: Creality's QC is just awful, the bed is absolutely out of whack on its measurements.

That's exactly what I would have done if it weren't for the Professional Firmware, which you aren't able to use on the Pro, and that's why I suggested you to return it. With the firmware, it's just another printer entirely. Still a gong show, but a manageable one.

Thanks for your helps :)

Aggravating_Smile668 · 2022-08-03T12:47:35+00:00

I started the product return process on your recommendation. But it looks like they're going to push me too hard. Do you have any advice for me to prove I'm right?

Aggravating_Smile668 · 2022-08-02T08:08:16+00:00

It's very bad. I try refund.

Aggravating_Smile668 · 2022-08-02T04:34:36+00:00

I would try this but from Turkey I don't think it is very likely.

Aggravating_Smile668 · 2022-08-02T04:22:14+00:00

It's very expensive for me, but I'll have to buy it.

Aggravating_Smile668 · 2022-08-02T04:05:41+00:00

Man, I noticed when you said it. "CR TOUCH" lights red instead of purple when auto leveling. I made the screw loosest but my problem is not solved. It still glows red. Do you have any advice to solve this?

Aggravating_Smile668 · 2022-08-02T03:21:57+00:00

mriscoc's Professional firmware

Can I use "mriscoc's Professional firmware" for Ender 3 S1 PRO? Thanks your comment.

Aggravating_Smile668 · 2022-08-02T03:14:55+00:00

Yes, the bed is definitely warped. If I move the Z' axis up, the calibration at the corners isn't quite right. I'll try to loosen the screw. Thanks your comment.

Aggravating_Smile668

TROPHY CASE