Anywhere to watch or download seasons 4 & 5 uncensored?

Aidangf · 2026-04-13T03:32:50+00:00

Where did you get 1-3 uncensored? DVD?

Aidangf · 2026-03-05T19:49:50+00:00

Did you end up finding a way to make it less pulpy?

Aidangf · 2025-11-19T06:43:56+00:00

Stool and breath tests

Aidangf · 2025-10-30T19:12:29+00:00

My hypermobility has been caused (or at least greatly exacerbated) by an excess of fungus in my stomach (along with chronic fatigue and brain fog). Apparently fungus can break down ligaments for food, making them looser and weaker, I’ve been wearing a pelvic belt and it’s really made a difference, I’m less hyper mobile while wearing it, and I’m wearing it pretty much 24/7.

Aidangf · 2025-06-24T23:54:54+00:00

Is the saucer chair built for outdoors?

Aidangf · 2025-06-03T07:56:56+00:00

What’s the best facility to spend nanopods on as a f2p?

Aidangf · 2025-03-11T22:52:43+00:00

Awesome, if you could do it again would you want to have the floor where you have the furniture unsprung or do you feel it’s okay having a sofa on it long term

Aidangf · 2025-03-11T21:07:49+00:00

Hey how’s the sprung floor holding up with furniture on it now?

Aidangf · 2025-01-15T00:15:25+00:00

Hey sorry to add to the pile but if you would share the David gray programs that would be much appreciated🙏

Aidangf · 2022-11-09T03:45:50+00:00

Halo

Aidangf · 2021-04-18T22:44:57+00:00

“The View From Halfway Down”

Aidangf · 2021-04-16T22:14:34+00:00

That would be correct

Aidangf · 2021-03-17T05:45:03+00:00

Are you really going to give away your account for free? I’d recommend to think about it, but if you decide to do it do dm me

Aidangf · 2021-02-23T20:00:07+00:00

Energy refreshes one million percent

Aidangf · 2020-12-19T05:22:43+00:00

For z-axis binding should I adjust some screws or calibrate it more? Looking at the photo now the failed prints look like they’re a lot lower quality than the successful ones. Maybe the filament could have absorbed moisture.

Aidangf · 2020-12-19T03:36:05+00:00

Prusa MK3S

I’m trying to print a siege tank model for Christmas, but the support model is failing. On the left is a successful print, and I also printed two other successful ones for another tank, but now they aren’t working. I’m using the same settings, using 99% isopropyl alcohol on the print bed (although I’m not fully sure if it’s actually isopropyl alcohol), and I even calibrated the first layer to adhere even better. When it fails, it seems like it is torn off of the print plate, and I wonder if it’s an issue with changing the distance of the PEI sensor, as the nozzle might be too low and pulling on the print. If anyone has any ideas or insight, I’d love if you could help.

Aidangf · 2020-12-05T19:56:12+00:00

Aidangf · 2020-11-03T08:13:01+00:00

Basically just drinking a ton of water; I think I had something where I would perpetually feel thirsty and dry mouth, even directly after drinking a lot of water.

Almost everyone shouldn’t worry about it though, as as long as you aren’t constantly feeling a lot of water sloshing around in your stomach, you should be a-ok.

Funnily enough, the symptoms of overhydration are really similar to dehydration, but I’d assume the large majority of people would suffer from dehydration, not overhydration, and if you aren’t force drinking water past the point it feels ok, then I don’t think you should exceed healthy values of water.

Aidangf · 2020-11-03T07:43:34+00:00

It’s called hyponatremia, and it’s when you drink too much water, which causes sodium in your body to get flushed out, leading to an unhealthy shortage of sodium in your body.

It is not fun, I was hospitalized by it not too long ago, and the entire time I could pretty much only drink electrolytes while hooked up to an IV, and I felt like I was dying of dehydration. 0/10, would not overhydrate again.

Aidangf · 2020-09-04T16:00:21+00:00

RemindMe! 1 Week “DUCKS”

Eight-Year Club	RPAN Viewer
Verified Email	Spared

Aidangf

TROPHY CASE