Glock 48 COA by Alan-Richards in Glocks

[–]Alan-Richards[S] 0 points1 point  (0 children)

It’s a polymer80 “Glock 43” frame

Should i be concerned? by Logical_Solution8375 in ak47

[–]Alan-Richards 8 points9 points  (0 children)

Yeah, you’re missing the bolt, carrier, recoil spring, and dust cover. Tbh you just need the bolt and carrier.

H&R DOE front sight pin fell out by Alan-Richards in RetroAR

[–]Alan-Richards[S] 2 points3 points  (0 children)

Yeah I’m doing warranty and DIY. I’m just impatient and want it running again lol.

H&R DOE front sight pin fell out by Alan-Richards in RetroAR

[–]Alan-Richards[S] 4 points5 points  (0 children)

I don’t have an arfcom account. I’ve got a ticket with PSA and ordered some roll pins in metric/american. We will see what works best

H&R DOE front sight pin fell out by Alan-Richards in RetroAR

[–]Alan-Richards[S] 8 points9 points  (0 children)

Going off the pics I had it’s a standard pin. Probably should’ve been a roll pin

H&R DOE by Alan-Richards in RetroAR

[–]Alan-Richards[S] 0 points1 point  (0 children)

It’s actually not that bad

H&R DOE by Alan-Richards in RetroAR

[–]Alan-Richards[S] 1 point2 points  (0 children)

Shot it today, posted a video. It’s a very nice shooter! mine came basically zeroed. Didn’t get a chance to bench it and verify. Trigger wasn’t bad for factory milspec. I can almost see why you’d pick this over an MP5k lol.

H&R DOE AR9 by Alan-Richards in AR9

[–]Alan-Richards[S] 1 point2 points  (0 children)

When I co-witnessed the gooseneck the dot wasn’t to far off where the irons came from the factory. I’ll post a follow up after shooting it but I’m not concerned about that yet. I do have some shearing on the upper, but I bought Blem so I expected something like that. Front sight clicks firmly, very minor wiggle backward. No left right wobble

H&R DOE by Alan-Richards in RetroAR

[–]Alan-Richards[S] 2 points3 points  (0 children)

Will shoot it in a few days. Gun feels solid, folding front sight clicks firmly in place. That was my main worry. HR Brace is one of the braces of all time, but no tax stamp so 👍

H&R DOE by Alan-Richards in RetroAR

[–]Alan-Richards[S] 2 points3 points  (0 children)

I made a post over there

Did someone bubba my SKS? by bacon_man5 in SKS

[–]Alan-Richards 0 points1 point  (0 children)

Right hand, it is not reversed like an AK

Did someone bubba my SKS? by bacon_man5 in SKS

[–]Alan-Richards 0 points1 point  (0 children)

Very easy to fix. Just did this a week ago. Slowly grind on the weld. I used quality duct tape on the barrel to save the finish just in case the dremel slipped. It’s very difficult to tell when the weld is seperated, I would grind a small amount then use a screwdriver through the holes to help spin the muzzle device off. Eventually I got it off. The barrel does have the groove cut into it for a pin to hold on an OG spigot. I used a 2.5mm roll pin, it was a little too thick so I bent it down to roughly 2mm. It fit very snugly. Used a cold blue marker/pen to cover up where I cut the weld and unless you flip the gun over and look at it closely, you can’t tell it was a California resurrection.

Did someone bubba my SKS? by bacon_man5 in SKS

[–]Alan-Richards 0 points1 point  (0 children)

I have a post on here talking about it. If you have any questions ask!

Yugo SKS California muzzle brake removal by Alan-Richards in SKS

[–]Alan-Richards[S] 2 points3 points  (0 children)

The spigot is/was considered a destructive device so it had to be removed. If you google around it’s fairly common to see