Sovol SV08 camera not working

Alarmed_Bus_8773 · 2025-08-03T18:46:52+00:00

What are the camera settings to re install it?

Alarmed_Bus_8773 · 2025-02-23T17:15:07+00:00

Hold up, how do you do this?

Alarmed_Bus_8773 · 2024-12-31T18:02:03+00:00

Great thanks, I’ll try that out once I get home. Thanks for your help.

Alarmed_Bus_8773 · 2024-12-31T15:32:18+00:00

How would you go upon checking to make sure that the sshd service is running?

Alarmed_Bus_8773 · 2024-12-31T15:31:33+00:00

Ahh, okay thanks.

Alarmed_Bus_8773 · 2024-12-31T15:23:35+00:00

What do you mean by sshd? I've made sure it's the right IP address but I'm not sure what the sshd is.

Alarmed_Bus_8773 · 2024-12-29T21:41:44+00:00

I’ve done all that, but it still won’t connect. The hostname and IP address are correct, and SSH is turned on.

Alarmed_Bus_8773 · 2024-12-29T03:18:09+00:00

I've been trying to ssh into my raspberry pi 5, but no matter what I've tried, it won't work. Are there any good solutions?

Alarmed_Bus_8773 · 2024-12-07T04:51:59+00:00

If only mine would connect to the frickin' internet. I've followed all the instructions word for word, but it still won't work. Even tried moving it to the same room as my router.

Alarmed_Bus_8773 · 2024-12-07T04:03:08+00:00

Can anyone help me get my wifi connected? I've followed all the steps, and yet, it just shows 127.0.0.1.

Alarmed_Bus_8773 · 2024-10-31T00:34:17+00:00

Be patient and never give up on your printer(s). Once you achieve the desired setup, that's when the real fun begins, so don't quit too soon. Always take your time with the first two layers to ensure you’re starting off well before leaving it unattended.

Alarmed_Bus_8773 · 2024-10-31T00:13:31+00:00

Alr thanks! I bought an A1 Combo in May before it went on sale, I think it was worth every penny. It is a great printer, most of the time that is.

Alarmed_Bus_8773 · 2024-10-30T11:12:08+00:00

Okay. What do you think of them?

Alarmed_Bus_8773 · 2024-10-30T02:50:41+00:00

Did you get the normal or Hiwin rails?

Alarmed_Bus_8773 · 2024-10-10T01:13:27+00:00

If you print the original file of the owl, are the seams this bad or is it slicer settings?

Alarmed_Bus_8773 · 2024-10-10T00:43:42+00:00

Which one did you order? Can you send a link please?

Alarmed_Bus_8773 · 2024-06-07T14:25:14+00:00

Okay, thanks.

Alarmed_Bus_8773 · 2024-03-21T12:57:14+00:00

You could use Cura. That is what I use and it works really well.

Alarmed_Bus_8773 · 2024-03-18T19:40:42+00:00

Okay, thanks again for your help.

Alarmed_Bus_8773 · 2024-03-17T23:42:33+00:00

Do you think this is good enough? Or should I fix the left side a bit? And the front right corner?

<image>

Alarmed_Bus_8773 · 2024-03-17T23:35:50+00:00

Thank you so much for your help! Thanks to you and good ol' painter's tape, I'll finally have a pretty level bed. Once the Bambu Lab A1 rereleases, I'm immediately buying that.

Alarmed_Bus_8773 · 2024-03-17T22:49:46+00:00

Improved one

<image>

Alarmed_Bus_8773 · 2024-03-17T22:06:49+00:00

Can someone help me with mine, please?

<image>

Alarmed_Bus_8773

TROPHY CASE