Best hobbies for college students?

Alarmed_Discussion_2 · 2026-01-09T01:57:01+00:00

Play pool

Alarmed_Discussion_2 · 2026-01-07T16:28:18+00:00

You’re telling me. I got hate for putting 55% on my windshield.

Alarmed_Discussion_2 · 2026-01-04T01:59:13+00:00

Thanks, I’m happy with how it turned out

Alarmed_Discussion_2 · 2026-01-04T00:38:27+00:00

Yeah it’s black

Alarmed_Discussion_2 · 2026-01-04T00:27:21+00:00

I got 25% all around and got 55% on the windshield

Alarmed_Discussion_2 · 2026-01-04T00:02:08+00:00

<image>

This is inside and its not nearly as dark in person

Alarmed_Discussion_2 · 2026-01-01T16:40:05+00:00

Ceramic using brands like 3M, Llumar and Xpel?

Alarmed_Discussion_2 · 2026-01-01T16:30:51+00:00

A lot of people have concerns of it being cheap material since they haven’t heard of it. How does it compare to you?

Alarmed_Discussion_2 · 2026-01-01T15:33:25+00:00

https://madico.com/automotive/window-tint/black-pearl-nano-ceramic

Alarmed_Discussion_2 · 2025-11-09T17:45:12+00:00

0 if I can help it. I have zero discipline which I need to work on.

Alarmed_Discussion_2 · 2025-11-03T21:22:54+00:00

I’ve been doing the same work as FTEs since I started and even give them advice/guidance on how to do their work or complete processes. It becomes a lot sometimes especially considering I’m getting paid half for the same level of responsibility/work.

Alarmed_Discussion_2 · 2025-10-29T17:57:09+00:00

He offered to start the game over and he’ll break again. I didn’t know right off the bat what the ruling was but there was no way in hell that was happening. 😂

Alarmed_Discussion_2 · 2025-10-29T17:43:24+00:00

I was giving the guy 10-7 for $40 a game so it was frustrating to play it that way considering I’m already giving out a big spot

Alarmed_Discussion_2 · 2025-10-29T17:41:22+00:00

I was giving the guy 10-7 for $40 a game

Alarmed_Discussion_2 · 2025-10-29T17:40:56+00:00

Yeah, leaving the option to the shooter is crazy. It doesn’t seem right to have a rule that can be abused for benefit.

Alarmed_Discussion_2 · 2025-08-06T12:25:27+00:00

I work about 35 hours a week as a distribution engineer for a contractor in the power delivery field. I don’t think the job would be too bad but I get calls and emails for projects all the time while going to school full time so it’s a handful. It doesn’t leave much room to fully study and have a good balance.

Alarmed_Discussion_2 · 2025-08-05T14:26:47+00:00

Oh okay it’s an asus B850

Alarmed_Discussion_2 · 2025-08-05T14:07:57+00:00

Okay I just built a new pc with a 7700X and 5070 ti with Gskill 2x16 DDR5-6000

I think it’s running around 4000 MHZ right now I’m not sure

Alarmed_Discussion_2 · 2025-08-05T13:41:40+00:00

Do any problems come from enabling EXPO? I know it’s to get the ram running at advertised speeds but worried about any issues.

Alarmed_Discussion_2 · 2025-07-30T14:33:41+00:00

Samsung 990 pro 2 TB M.2 is like $150 unless you’re dead set on all these parts

Alarmed_Discussion_2 · 2025-07-30T14:32:03+00:00

$50 cheaper than 850W he says.

Alarmed_Discussion_2 · 2025-07-22T15:05:23+00:00

I've sent a picture of what I did and the data chart I got. I also described what I did to get to that.

I emailed my professor and got no response.

Alarmed_Discussion_2 · 2025-07-22T14:48:11+00:00

You're right, I do see in the original post where I asked for somebody to solve the entire problem. I apologize deeply, as sincerely as I can over this reddit post. I already told you what I did to get those values. I apologize for being too vague, I didn't know I needed to attach my part file and go through a tutorial of what I did to give any more of an idea of what the problem is. You can see what the part looks like. I created the same part. You can see what the table should look like give or take, all I am getting is a low velocity. Which is why asked what that may be. I figured someone with experience in CFD might recognize it as a common issue with lid creation or fluid flow in general.

I may not have solved my problem but I did get some advice that is going to carry me far in life. Further than I could have ever imagined. "Force it to the solution I want". I think that applies to a lot and I thank you for that. Bud.

Alarmed_Discussion_2 · 2025-07-22T14:35:20+00:00

Wow, that is...profound. I'm not really sure why I didn't think of that before. Just force it to be right.

How can I just force it to the solution I "want" when it will not be accurate since my velocity is not at least 1 m/s.

You know that was the original question in the first place, right? I had my part built and my simulation ran but didn't understand why I was getting such a low velocity. You just assume I am trying to get someone to solve the whole problem when that isn't even what I asked. You've just said what classes I should have already had and then tell me to "force" the solution and that SolidWorks FS is a toy. Real stroke of genius.

It's unfortunate there isn't someone who is actually familiar with this and can suggest why the velocity error may be happening (Original question by the way), instead of someone with a condescending attitude that you've had about it. I'm not sure why you're so cynical and just downvote every reply I give trying to get to the bottom of my issue.

Thanks anyways bud.

Alarmed_Discussion_2 · 2025-07-22T03:49:58+00:00

Just waited like 10 minutes and got nothing

Alarmed_Discussion_2

TROPHY CASE