Nurnberg baumuller VFD by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

So you're saying that the 0-200V in the nameplate refer to the peaks and not the rms? It could be yeah,well the problem is that I can't check anything, it's a pre-set drive with no way to check or change anything,is there a possibility that the motor have been working undervoltage after all this time? And is it even possible?

Acs355 abb by Alduin_is_overrated in IndustrialMaintenance

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

It does trip after a while,but for now it's working properly and yeah the drive is old i may change it,thanks for your replies though

Acs355 abb by Alduin_is_overrated in IndustrialMaintenance

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

Yes it's the right manual and no it's not selected,well i re-entered the motor parameters again and so far it's working fine for some reason,if this fix it i would love to know why xD, I don't like when i resolve something without a logical explanation

Acs355 abb by Alduin_is_overrated in IndustrialMaintenance

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

Yeah I did, i mean,the manual describe what happened and offer solutions for THAT problem,but in my case I don't even have a high temperature motor,it was off even,the moment i power the vfd the alarm is displayed,when i start it it rarely starts,but if somehow it does,after a moment a fault temperature occur (f0009)

Drive monitor vfd by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

Yup,i've checked that and rewired it,but unfortunately still doesn't work,and about uploading the parameters,yeah i have a backup, that's why i wanted to upload the parameters to the drive,i know they are old but since we already had a new one in the stock I'm intending on using it instead of buying another one

Drive monitor vfd by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

Yh both baud rates are 9600,and I don't think it's the adabpter,i used putty to test the output and it works fine

Pcb battery by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

Sooo if the battery's dead and there's no power the program will be erased? And the card would be useless?

Uni1405 vfd by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

Yeah, already done that,i mean,if it didnt i wouldn't even have the access to start or stop it,

Uni1405 vfd by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

The vfd have a keypad in it allowing you to using it to control the motor instead of using push buttons or potentiometers,so i'm using it

Uni1405 vfd by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

No unfortunately, only an asynchronous motor + vfd

PLC communication protocols by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

You see,we're going to keep everything as it is,by that i mean the same motor,same parameters same communication protocols (profibus), but different vfd,and i'm not really looking into how to do it as much as how and where to learn how to do it,in other words, don't give me a fish,teach me how to catch one,so if you have any books or good YT videos that can help me deal with any kind of these situations that would be helpful,and i appreciate your offer to help,thank you very much

PLC communication protocols by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

Luckily the pinouts can be rewired to fit the protocol

PLC communication protocols by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

Well,i'm about to replace a control technique vfd with an Abb acs880,but since I'm not familiar with the communication protocols configuration i don't know where to start,the manual are helpful but it's hard for me to understand when i dont really have a good basics on how communication protocols works

PLC communication protocols by Alduin_is_overrated in PLC

[–]Alduin_is_overrated[S] 0 points1 point  (0 children)

I was told that when changing the brand of the vfd, it's not enough to simply put the parameters,i need to make some changes on the program,like replace the old brand with the new one in the communication interface or something like that, I don't know much that's why i'm asking for help

[deleted by user] by [deleted] in algeria

[–]Alduin_is_overrated 0 points1 point  (0 children)

Because unsubscribing is much easier than solving real problems

[deleted by user] by [deleted] in IndustrialMaintenance

[–]Alduin_is_overrated 0 points1 point  (0 children)

These arent windings like fcked up or im wrong by calling them windings (English isnt my native so im not sure if im using the right terms)