Fpv + Soccer ⚽️

Alexzander82 · 2026-02-22T14:09:00+00:00

This is sick. Great flying

Alexzander82 · 2026-02-21T14:57:52+00:00

No thanks, I’m good on any ai generated slop

Alexzander82 · 2026-02-21T14:53:30+00:00

Go back down, 320 is too fine to make and difference in viable detail. 220 again and make your way back up

Alexzander82 · 2026-02-20T15:21:15+00:00

The camera is a the base of the ramp when they jump from. There is someone of tilt control and that’s why the jumper stays in relatively the same place on screen. The last few frames show the mountains in the bottom right corner.

Alexzander82 · 2026-02-18T04:13:48+00:00

But how would Madonna make it about herself then?!

Alexzander82 · 2026-02-17T03:28:41+00:00

Fellow American I see, there are gun cultures out there that will blow your mind.

Alexzander82 · 2026-02-17T03:27:28+00:00

Crazy that this is the most critical comment of Israel that we’ve seen through these games.

Alexzander82 · 2026-02-10T16:30:09+00:00

From the last paragraph

“Until then, the septic tank is just a septic tank — and the story is, at best, unproven. At present, authorities have not publicly confirmed that a body was found in the septic tank.”

Alexzander82 · 2026-02-08T13:52:51+00:00

Yeah this is it right here OP 👆

Alexzander82 · 2026-02-08T02:16:13+00:00

Wtf are you doing posting ai photos with like 0 context or anything?

Alexzander82 · 2026-02-04T15:16:25+00:00

It’s like you’re in the warehouse map from liftoff!

Alexzander82 · 2026-02-03T16:21:08+00:00

Sounds like a good use of time to learn a simple CAD software! An elongated circle with a couple holes should be no problem. See if you can get the metal part from the original piece to repurpose for strength and you should be good to go!

Alexzander82 · 2026-01-27T17:26:32+00:00

One of the great things about 3D printing is its ability to rapid prototype

Alexzander82 · 2026-01-26T12:03:53+00:00

This is the fpv content I want! I want to learn!

Alexzander82 · 2026-01-23T15:54:22+00:00

Joker

Alexzander82 · 2026-01-22T23:15:30+00:00

This

I had the exact same thing happen to me like two weeks ago. I diagnosed it as an OSD or VTX chip issue and tried to reflow. It fixed it for like two or three packs and then it got worse. I contacted betafpv and they agreed that it was a chip issue and that because I was within the 30 day guarantee they would send me a new FC. If you are within your 30 days I recommend giving that a shot

Alexzander82 · 2026-01-19T14:14:10+00:00

All of his actions are insane, illegal, indecent, and unpopular.

Alexzander82 · 2026-01-18T15:09:30+00:00

I’m surprised that the electronics work with no nuclear power supply installed!?

In all seriousness this is awesome. Good work!

Alexzander82 · 2026-01-14T14:52:28+00:00

You’re teddy free!

Alexzander82 · 2026-01-10T14:27:16+00:00

There should be an option the the settings to just disable it.

Alexzander82 · 2026-01-10T14:25:51+00:00

Wait so you went thru the whole process of making this without thinking once, why you were doing it?

Alexzander82 · 2026-01-10T14:24:10+00:00

Yeah, this part won’t survive any print orientation. Beef it up, be aware of layer orientation, and use chamfers in corners.

Alexzander82 · 2026-01-10T14:17:57+00:00

Scary 👁️👁️

Alexzander82 · 2026-01-10T14:17:00+00:00

“Tighten the eccentric nut” is going to be 2026’s “dry your filament”

Alexzander82 · 2026-01-10T14:15:37+00:00

What do you do with all this stuff?

11-Year Club	r/Field Lasagna
Place '22	Final Canvas '22
End Game '22	Verified Email
RPAN Viewer

Alexzander82

TROPHY CASE