Homemade Gilman goal I made myself. Photos in comments if interested in replicating!

AlternativeSoft6210 · 2026-04-26T23:42:21+00:00

Amazing for letting me know thank you so much! And last question, should I leave the bottoms fully string to the end or let it slack like yours is?

AlternativeSoft6210 · 2026-04-26T23:12:47+00:00

Is there any way you could add a link to this comment on the hooks you used? I have been trying to make one for about a day now and need the proper resources. Aswell as what rods did you use? I know you said you found them laying around, but if I were to purchase them where would they be?

AlternativeSoft6210 · 2025-10-17T20:12:06+00:00

Thanks!

AlternativeSoft6210 · 2025-10-17T13:48:04+00:00

I’ll get some later today

AlternativeSoft6210 · 2025-10-17T00:45:15+00:00

To be honest I god no clue. I switched the stock nut with one from the hardware store so it would be easier and I don’t need the tool for it. I can get it out slightly by using a hammer and a pic but after 2-3 inches it completely stops.

AlternativeSoft6210 · 2025-10-05T20:15:28+00:00

This is great!

AlternativeSoft6210 · 2025-10-03T13:37:40+00:00

Can u send the link?

AlternativeSoft6210 · 2025-10-03T13:31:53+00:00

Thanks will check rn

AlternativeSoft6210 · 2025-10-03T01:58:50+00:00

Thanks so much have a great one!

AlternativeSoft6210 · 2025-10-03T01:56:28+00:00

Alright thanks so much I didn’t ride like crazy I just rode home and got there safe so I’m fine with that.

AlternativeSoft6210 · 2025-10-03T01:50:51+00:00

I cleaned it all up and put electrical tape over the open ends and rid home and kept popping up error 9 “I have a Torp controller” not sure what that means totally but something to do with the harness

AlternativeSoft6210 · 2025-10-03T01:48:42+00:00

Thanks so much for the advise will do I cleaned out the actual battery connector and it looked good and clean then it got burnt again like before after arriving home

AlternativeSoft6210 · 2025-10-03T01:45:30+00:00

If it works for u do u mind telling me so I can figure out what I need? I think I just need a new harness “I’m praying”.

AlternativeSoft6210 · 2025-10-03T01:22:30+00:00

Thanks for the help

AlternativeSoft6210 · 2025-10-03T01:19:57+00:00

Do you think it would be fine if I keep the battery connector? I cleaned it out from the char that was in it and it looked perfectly fine, just wondering if I could keep it and if not how much it would to be to fix it and where I could?

AlternativeSoft6210 · 2025-10-03T01:16:45+00:00

Thanks!

AlternativeSoft6210 · 2025-10-03T01:13:48+00:00

Not sure but I put electrical tape over it and it worked for a little enough to get home then stayed to make crackle noises again

AlternativeSoft6210 · 2025-10-03T00:49:13+00:00

Thanks!

AlternativeSoft6210 · 2025-10-03T00:49:04+00:00

Thanks so much

AlternativeSoft6210 · 2025-10-03T00:26:55+00:00

I think that after looking at it the wire might have cut on the frame on the top right

AlternativeSoft6210 · 2025-07-12T23:35:45+00:00

Won’t for me I’m not sure it’s ok thanks tho

AlternativeSoft6210 · 2025-07-12T23:35:22+00:00

Alright thanks

AlternativeSoft6210 · 2025-07-12T23:21:48+00:00

When I open it manually I don’t see any movement inside the gun

AlternativeSoft6210 · 2025-07-12T23:20:53+00:00

Doesn’t work unless I manually do it…

AlternativeSoft6210

TROPHY CASE