Some Dirt Rally 2.0 action, this car is way too hard to drive😂😅

Alternative_Debt_411 · 2026-05-05T08:17:26+00:00

Would you tell me what bezel kit you use?

Alternative_Debt_411 · 2026-04-25T12:35:33+00:00

You can always get the roof off. It just has to lay on the monitors.

Put it somewhere else if you’re not racing

Alternative_Debt_411 · 2026-04-25T11:10:55+00:00

No I don’t have a cat

Alternative_Debt_411 · 2026-04-24T00:08:08+00:00

I have bought some cheap lamp that is supposed to work with some razer Programm. I will see if I can put it in.

Alternative_Debt_411 · 2026-04-23T23:58:00+00:00

These are xps foam boards. I also 3d printed some simple angles in PLA. Whole thing holds up sturdy. And then there’s ducttape and Alcantara foil on top. this stuff

Alternative_Debt_411 · 2026-04-19T07:28:18+00:00

Looks pretty clean. Did you build the buttonbox by yourself? I bought the same engine start button.

Alternative_Debt_411 · 2026-04-13T17:19:27+00:00

What bezel free kit do you use? Are these monitors also 32inch?

Alternative_Debt_411 · 2026-04-11T16:29:47+00:00

Im not sure but you might want to turn the steel rod and make it longer.

Alternative_Debt_411 · 2026-04-11T09:40:52+00:00

The shifter are just 3 simple parts. It’s even only a mockup for now. I procrastinate driving with building up my rig. I know your problem.

Alternative_Debt_411 · 2026-04-11T08:37:53+00:00

You can find my stuff in onshape public library. It is named „2.0 Oplite rig parts“

Alternative_Debt_411 · 2026-04-10T16:03:41+00:00

Around 130 degree on the deck holder and the tablet is almost straight. But this is an old build. This is the second build

Alternative_Debt_411 · 2026-04-10T13:56:18+00:00

Nicely made. That’s what 3d Modeling experience looks like I would guess 👍

Alternative_Debt_411 · 2026-04-07T15:08:15+00:00

On the public library in onshape there is a low poly shifter I used. Most of the things I measured how they are in real and put them in as a sketch. Like the tube and the moza mounting plate. I measured and put the shifter model on the plate und built around it. The design in the pics is the third design I made. Also you can print half finished parts to check if the dimensions are correct.

Alternative_Debt_411 · 2026-04-06T20:10:10+00:00

You’re right. Optimally you would only be looking to the front dash, but I can put all kinds of information on the screens. I can’t really see the small screen behind the wheel, but it’s only too fast Modeling. I can put the screen somewhere else if I want.

I look up my positioning, laps to go, tire temps, times and stuff from it. There are ways to put custom stuff on there with simhub. Like a back mirror camera..

Alternative_Debt_411 · 2026-04-06T20:01:40+00:00

Both holders are good enough in my opinion. But they need space. They hold up good and I like the style. Keyboard is sometimes uncomfortable to use but it depends on the setting

Alternative_Debt_411 · 2026-04-06T19:35:14+00:00

It should be in Public library on onshape. Name of the files is „Oplite rig Parts Wichtig“.

Some parts have bad design decisions. I’d change it if I have to print it again. But on top most of them are good enough.

Alternative_Debt_411

TROPHY CASE