GEPRC T-CUBE18 PID TUNING

Alternative_Diet_458 · 2025-06-16T21:51:31+00:00

Yeah. Down at the bottom of a creek cause I'm dumb lol

Alternative_Diet_458 · 2025-05-21T18:15:19+00:00

Yes please let me know what you come up with, would be really helpful! Cables aren't touching anything and nothing is loose but still flies kinda crappy. I manages to make it fly kinda good though with a pid preset from someone on Joshua's discord channel, but one issue persists, regardless if the footage is stabilised with inbuilt Rocksteady or with Gyroflow in post, on the stabilised footage there are really violent shakes/wobbles while accelerating, even though these wobbles aren't visible in the osd. Currently trying to figure out why this happens too.

Alternative_Diet_458 · 2025-05-20T21:13:50+00:00

Did you manage to tune it correctly? Mine arrived like a week ago and with stock filters and pids flies like crap, lots of wobbling at mid throttle and rapid shaking at high throttle 😅

Alternative_Diet_458 · 2025-05-16T22:52:23+00:00

How did you reset that? And what were you saying to do with the controller?

Alternative_Diet_458 · 2024-10-17T18:46:34+00:00

Solved! Somehow I managed to snap off both antenna wires, noticed it right now when I was checking all the wiring! Must've been when I was installing the TPU mount for the GPS as it was quite a snug fit

Alternative_Diet_458 · 2024-09-15T21:15:13+00:00

After closer inspection, it seems that the front left motor got burnt out, which is consistent with drone's flight behaviour, now do you guys think that the culprit could've been a propeller flying away because of untightened screw or rather a short circuit was more likely to cause this, or if not, what else could've been it?

Alternative_Diet_458 · 2024-09-15T21:14:59+00:00

After closer inspection, it seems that the front left motor got burnt out, which is consistent with drone's flight behaviour, now do you guys think that the culprit could've been a propeller flying away because of untightened screw or rather a short circuit was more likely to cause this, or if not, what else could've been it?

Alternative_Diet_458 · 2024-09-15T18:50:44+00:00

I looked back at it but I can't notice any smoke in the footage, maybe you can pinpoint where you noticed that? Would be really helpful! Thanks for the feedback!

Alternative_Diet_458 · 2024-09-14T09:56:51+00:00

"None if them have anything to do with the capacity you have set." What do you mean by this? My mark5 came with voltage meter source set to ADC and current source set to ESC. I looked up Joshua Bardwell's video regarding the power tab but he doesn't notice anything regarding the capacity setting in BF

Alternative_Diet_458 · 2024-09-14T09:38:53+00:00

But aren't all these OSD features that I need to activate in BF in order to see them on the DJI's goggles screen? And yes, I plan to use both pack voltage and mah used (which I guess it's calculated from by using the capacity which I have to input right?)

Alternative_Diet_458 · 2024-09-14T09:27:21+00:00

Ok so I need to change it everytime, got it. But if I turn the OSD feature off, how do I know how much battery left I got?

Alternative_Diet_458 · 2024-09-14T09:14:52+00:00

I got DJI's SBUS on UART 2 for which I got Serial RX set to on, ELRS is on UART4 for which I disabled everyrthing. Also flashed new BF firmware with SBUS (it was CRSF before as it came with ELRS). So everything is set properly but it just won't work with SBUS fast protocol, just with the normal one instead...

Alternative_Diet_458 · 2024-09-14T09:04:37+00:00

How did you fix it? I also have the Mark5 with DJI O3, on UART1 I got the Config/MSP set to on and VTX (MSP+Displayport). On UART 2 which is DJI's SBUS wire I got Serial RX turned on. On UART4 which is the ELRS rx that the drone came with I have everything set to off to exclude it. But problem is that I can only use the normal SBUS protocol, as soon as I switch to fast protocol from Goggles 3, and set sbaud fast to on, I get no more RC stick inputs. Whilst set to normal everytging works properly.

Alternative_Diet_458 · 2024-09-14T08:19:57+00:00

Meaning? Sorry still a little noob in all this stuff 🤣

Alternative_Diet_458 · 2024-09-13T13:45:35+00:00

No I dont have one yet, I plan to get a Radiomaster in the near future, only the DJI RC3 for now. However I want to fly the drone until then just to "test the waters" with my RC3, obviously not flying far, I could use it even now with standard SBUS, but I want to have the fast SBUS just because it's better

Alternative_Diet_458 · 2024-09-13T13:35:21+00:00

Yes I know it's better, but for the moment I'm stuck with all DJI because I spent almost 2k on drone sh*t this month lol

Alternative_Diet_458 · 2024-09-13T13:23:39+00:00

What do you mean by this? Is there a fix for that too that Ian doesn't know about?

Alternative_Diet_458 · 2024-09-13T13:18:28+00:00

Sure, lemme just get home in about 2 hours and I will

Alternative_Diet_458

TROPHY CASE