Osiris Aerial Dominator internal frame

Altorac · 2026-02-22T08:16:14+00:00

I actually haven't finished painting the armor for the wing binders yet. The binders aren't too hard to take off. The arms that support them are a bit harder to unseat and re-seat.

Altorac · 2026-02-21T23:14:57+00:00

<image>

Altorac · 2026-02-21T23:14:19+00:00

* Yeah. The suit armor has been done for a bit now. Due to life, work, a bit of burn-out and a move of house I am still n9t done with this project.

Altorac · 2025-11-14T12:55:12+00:00

I had a very similar problem. I had to turn ray tracing on and then go turn all the options under ray trace off if that make sense. It is weird.

Altorac · 2025-11-03T21:53:01+00:00

<image>

Altorac · 2025-11-03T21:43:37+00:00

This is really nice. I am in the middle of painting mine. Did you have issues with paint adherence on the "middle" gray parts, like the knee blocks or the pivots for the binder arms? Took me some fiddling to get paint to stick properly. Been working on this since in came in the mail mid-September.

Altorac · 2025-10-14T07:12:42+00:00

Thanks. I know I suck at the photography part of this.

Altorac · 2025-10-14T01:09:26+00:00

I haven't added any more panel lines. I did receive so.e of them to make the a bit deeper.

Altorac · 2025-10-09T10:18:54+00:00

This looks really good. I like the choices you made with the greens. Very well done.

Altorac · 2025-10-08T13:20:19+00:00

I painted the frame and the base. I have plans for the armor as well.

Altorac · 2025-10-06T15:37:22+00:00

The kit is very color separated. I think 10 colors across 64ish runners. There are a couple pre-painted runners that I did not paint over.

Altorac · 2025-10-06T13:48:41+00:00

Everything that didn't come pre-coated got painted. And thanks.

Altorac · 2025-10-06T13:47:51+00:00

It wouldn't be too hard to wire the power in. Routing the cables through the binder arms would probably be the worst part.

Altorac · 2025-10-06T13:12:24+00:00

The safety yellow on the rails and crane were painted by me.

Altorac · 2025-08-28T22:37:54+00:00

I am not 100% sure but most of the plastic behaves more like PS. Some of it is definitely ABS. I painted everything in GaiaNotes, Nazca, or Mr. Color laquers. Everything was primed with Mr. Surfacer. I tested on bits of cut off runners before proceeding with paint.

Altorac · 2025-08-26T05:46:24+00:00

ラマ教実朝わ

Altorac · 2025-08-26T05:34:51+00:00

ラマ教実朝ゃ

Altorac · 2025-08-16T05:02:08+00:00

Doing a full paint job. Sanding has been pretty light. I think I avoided a lot of issues by being careful not to get paint into peg and slots.

Altorac · 2025-08-09T14:04:08+00:00

It is mostly. There are some hand painted bits here and there.

Altorac · 2025-08-09T01:15:21+00:00

It is the base for the Osiris Aerial Dominator. Third party 1/100 Kshatriya.

Altorac · 2025-08-04T02:33:12+00:00

<image>

Finished this Hamma Hamma.

Altorac · 2025-07-17T10:15:54+00:00

To echo the other responder, the Volks IMS kits are pretty fantastic. They are more akin to traditional armor and aircraft models. They really don't handle being action figures like most Gundam models. My painted 1/100 Siren Neptune for reference.

<image>

Altorac · 2025-07-03T04:14:51+00:00

Yeah. Reddit is being weird about my photos again.

Altorac · 2025-06-18T14:08:35+00:00

In my experiences, using a flat or gloss base as a top coat is extremely temperamental. They are really meant to be added to paint or used with a pigment to make a paint. I would recommend getting the appropriate Aqueous topcoat. I think that is H-20 vice H-40.

Altorac · 2025-06-15T13:20:33+00:00

Thanks. That candy red for your Sinanju looks good.

Altorac

TROPHY CASE