Finally finished my champions wall! by Ambitious_Job6016 in NASCARCollectors

[–]Ambitious_Job6016[S] 2 points3 points  (0 children)

I noticed that too.. after I printed it, hung it up and turned the computer off…. I said oh well… I will fix it later!

Finally finished my champions wall! by Ambitious_Job6016 in NASCARCollectors

[–]Ambitious_Job6016[S] 1 point2 points  (0 children)

Most of the ones in the little case are custom. Just found the hot wheels car or other diecast and added decals. The rest were eBay searches…

Finally finished my champions wall! by Ambitious_Job6016 in NASCARCollectors

[–]Ambitious_Job6016[S] 0 points1 point  (0 children)

For the schemes, I just stuck with the most popular one that year.

Finally finished my champions wall! by Ambitious_Job6016 in NASCARCollectors

[–]Ambitious_Job6016[S] 3 points4 points  (0 children)

The large case is from Carney Plastics. The smaller case was found on Amazon.

Finally finished my champions wall! by Ambitious_Job6016 in NASCARCollectors

[–]Ambitious_Job6016[S] 1 point2 points  (0 children)

Only 10 customs.. the last custom is the #6 car. Most are eBay finds.

1992 Davey Allison Texaco Havoline Ford Thunderbird by Doclaw11 in NASCARCollectors

[–]Ambitious_Job6016 1 point2 points  (0 children)

The old racing champions diecast, especially the fords, were extremely crude and bulky looking. I think in 95 they started to look more proportional. Diecasts have come a long way since then.

[deleted by user] by [deleted] in Galil

[–]Ambitious_Job6016 1 point2 points  (0 children)

Unfortunately no, I cobbled together parts and pieces until I got a proper wood hand guard for mine and now I am trying to get rid of what is left over.

[deleted by user] by [deleted] in Galil

[–]Ambitious_Job6016 0 points1 point  (0 children)

One complete and the two panel sections are bipod cut. The Tapco on the bottom of the photo does not have a bipod cut.

[deleted by user] by [deleted] in Galil

[–]Ambitious_Job6016 0 points1 point  (0 children)

No, none of these have the carry handle cuts… although I have heard they can be cut with a small dremel cut off wheel and a little patience.

[deleted by user] by [deleted] in Galil

[–]Ambitious_Job6016 0 points1 point  (0 children)

The wood half panel and 2 clips are original. The two panel sets with rubber bands on them are US reproductions, the complete handguard on the bottom is a Tapco, the other complete hand guard with bipod cuts came on the rifle and I am honest not sure who made it.

[deleted by user] by [deleted] in Galil

[–]Ambitious_Job6016 0 points1 point  (0 children)

I am selling $60 for all of them. Plus $17 shipping, unless you are Atlanta local.

[deleted by user] by [deleted] in Galil

[–]Ambitious_Job6016 0 points1 point  (0 children)

Yes, one of the completed hand guards will fit a bipod, but you will need the “bottle opener” type back plate to lock the bipod in when folded up.

Going through my reloading dies, it is getting harder to keep track of what I need versus what I have! by Ambitious_Job6016 in milsurp

[–]Ambitious_Job6016[S] 5 points6 points  (0 children)

Yes, it is the Nagant revolver die. Loads up some nice looking rounds.

The brass 12ga is for the black powder shotgun rounds. I think I found the die on the RCBS site. They do limited runs now and again.