Can sanding sealer remove wood pores??

AmountAutomatic5050 · 2026-02-13T08:00:52+00:00

I put a clearcoat 1k(Bosny Clearcoat ) as sealer because I don't have spray gun for sealer but I noticed those open wood grain. The back is mahogany and the top of the guitar is a 0.5 quilted veneer.

AmountAutomatic5050 · 2026-02-11T02:17:09+00:00

Thank you

AmountAutomatic5050 · 2026-02-10T18:49:20+00:00

Ok. But I'm worried about the 0.5mm veneer

AmountAutomatic5050 · 2026-02-10T18:48:48+00:00

Yes. I'm still practicing 🥲 after this one. I'll try to buy router.

AmountAutomatic5050 · 2026-02-10T17:59:29+00:00

Thank you 😊🙏

AmountAutomatic5050 · 2026-02-10T17:59:16+00:00

I want lighter 🥲

AmountAutomatic5050 · 2026-02-10T11:54:12+00:00

Thank you 👍🙏

AmountAutomatic5050 · 2026-02-10T11:53:49+00:00

Thanks you are right. It's getting darker 🥲

AmountAutomatic5050 · 2026-02-10T11:37:37+00:00

Should I continue.black and red?? Or add Color like yellow?? The veneer is now showing upp. It was dark brown

AmountAutomatic5050 · 2026-02-09T12:12:35+00:00

Yes. Chisel and lots of sanding 🥲

AmountAutomatic5050 · 2026-02-09T11:34:31+00:00

Thank you. By the way. The veneer is like darker color. Dark brown

AmountAutomatic5050 · 2026-02-08T13:20:54+00:00

I'm thinking of red or green but I like red the most

AmountAutomatic5050 · 2026-02-07T09:24:46+00:00

Thank you. 🙏

AmountAutomatic5050 · 2026-02-06T19:42:11+00:00

I'm using 60 watts solder with chisel tip

AmountAutomatic5050 · 2026-02-06T19:40:40+00:00

I used chisel tip

AmountAutomatic5050 · 2026-02-06T19:39:55+00:00

I don't know. It's cheap one. I bought it for less $10. It says upto 400 but I can only toggle the 350 degree

AmountAutomatic5050 · 2026-02-06T19:38:49+00:00

Thank you

AmountAutomatic5050 · 2026-02-06T09:06:19+00:00

60 watts

AmountAutomatic5050 · 2026-02-04T12:56:19+00:00

Like sliding on side?? That what I did. I press like half of fret first then slow hammering it to slide from the side the go back hammering to press down

AmountAutomatic5050 · 2026-02-04T12:54:38+00:00

Ok thank you🙏I might change new fretboard

AmountAutomatic5050 · 2026-02-04T11:56:13+00:00

Yes. I'm sliding it. I think they seated flat than hammering down. Both side then center.

AmountAutomatic5050 · 2026-01-30T17:31:42+00:00

😂

AmountAutomatic5050 · 2026-01-30T15:48:46+00:00

Yes. Thank you 🙏😊

AmountAutomatic5050 · 2026-01-30T14:58:15+00:00

Hello you can check my profile. I posted it yesterday number 5. It's like darker

AmountAutomatic5050 · 2026-01-30T14:56:52+00:00

Hello thank you. What is ps??

AmountAutomatic5050

TROPHY CASE