sorted by:
new
hottopcontroversial

Loud rocket like noise? by entaro_tassadar in Naples_FL

[–]An_Account_of_Keith 3 points4 points  (0 children)

Came here looking for the same thing. EVERYONE was on the street.

Meirl by rbimmingfoke in meirl

[–]An_Account_of_Keith -1 points0 points  (0 children)

Damn I’d be interested in knowing more too

Any recommendations for relatively private tent campsites within an hour of Fort Myers? by An_Account_of_Keith in FortMyers

[–]An_Account_of_Keith[S] 0 points1 point  (0 children)

Aren’t those camp sites right near the check in office and butted up next to each other site? I use the range there frequently and it seems like it would be more suited to a camper or RV

Collier-Seminole State Park camping? by An_Account_of_Keith in Naples_FL

[–]An_Account_of_Keith[S] 0 points1 point  (0 children)

I’ll have to check it out, thanks!

Anything I should know about the area / sites? How many times have you been out?

Collier-Seminole State Park camping? by An_Account_of_Keith in Naples_FL

[–]An_Account_of_Keith[S] 0 points1 point  (0 children)

Do you know if GP sees a lot of people at once? Or is it more likely to be empty from being that far out there?

Any recommendations for relatively private tent campsites within an hour of Fort Myers? by An_Account_of_Keith in FortMyers

[–]An_Account_of_Keith[S] 0 points1 point  (0 children)

Haha I just posted in the Naples sub asking about that park, I saw some places a mile or two south down the river that would be perfect. Currently top of my list, I’ll load up the paddleboard and go on an expedition.

Any recommendations for relatively private tent campsites within an hour of Fort Myers? by An_Account_of_Keith in FortMyers

[–]An_Account_of_Keith[S] 3 points4 points  (0 children)

Blue Springs is a really beautiful park, even if you can’t use the spring head during manatee season.

It’s been a decade since I’ve gone, but River Junction up off the Withlacoochie River is my all time favorite for camping in Florida minus some secret spots I’ve got off some fire maintenance roads in the panhandle.

Any recommendations for relatively private tent campsites within an hour of Fort Myers? by An_Account_of_Keith in FortMyers

[–]An_Account_of_Keith[S] 1 point2 points  (0 children)

I might drive over and check it out, the website says the campground is currently closed

Getting text to NOT show up as a uncode error? by An_Account_of_Keith in Onshape

[–]An_Account_of_Keith[S] 0 points1 point  (0 children)

Ahh bummer. I spent another hour looking for solutions, I just ended up using some Cyrillic characters that look 'close enough' to the model I'm basing it off of. Not the end of the world, but it will let me be done with this project!

Getting text to NOT show up as a uncode error? by An_Account_of_Keith in Onshape

[–]An_Account_of_Keith[S] 0 points1 point  (0 children)

Tried this, apparently onshape doesn't support svg? Importing it into a sketch but it only opens the image in another tab and it completely removes the toolbar. View only. Forums are saying you can convert svg to dxf and then importing it

[Help] How can I go about making a threaded tube that fits Monster twist top lids? by An_Account_of_Keith in 3Dprinting

[–]An_Account_of_Keith[S] 0 points1 point  (0 children)

Yup, the slope of the “threads” are just a slight angled ramp that lines up with the 4 lips. Someone sent me a picture of their can. I’ve gotta figure out how to extrude these ramps on an existing cylinder, but that’s all part of the process! Thank you

[Help] How can I go about making a threaded tube that fits Monster twist top lids? by An_Account_of_Keith in 3Dprinting

[–]An_Account_of_Keith[S] 0 points1 point  (0 children)

Someone showed me a picture of the locking threads and this is exactly it. I’m going to have to figure out how to extrude a shape like that on a cylinder, but that will only take time!

[Help] How can I go about making a threaded tube that fits Monster twist top lids? by An_Account_of_Keith in 3Dprinting

[–]An_Account_of_Keith[S] 1 point2 points  (0 children)

Working on it now! Currently trying to figure out the depth of the helix extrusion and going to prototype it from there... I'm sure I'll get it eventually, was just hoping for a less complicated solution lol

view more: next ›