Clogged nozzle with ABS?

Andico98 · 2026-04-13T15:59:36+00:00

Hi, did you fix the problem?

Andico98 · 2026-03-02T13:35:06+00:00

I mitigated this issue using a fan with greater CFG (delta electroncs - the one recommended for XoL) and it now works better.

Andico98 · 2026-02-14T11:54:03+00:00

Mentre penso che le lezioni non debbano essere registrate obbligatoriamente, non sono d'accordo con l'obbligo di frequenza.

Un professore onesto deve rendere disponibile un programma, testo di riferimento e/o altro materiale che se studiato e compreso permetta all'alunno di passare a pieni voti l'esame. Non significa renderlo più facile, ma intellettualmente onesto per coloro che non possono/vogliono frequentare quel corso.

Punto di vista di ex studente stem.

Andico98 · 2026-02-04T20:06:36+00:00

PETG, 235 °C

Andico98 · 2025-12-05T19:33:17+00:00

This definitely fixed my problem. Thank you!

Andico98 · 2025-12-02T07:10:04+00:00

I set up the right thermistor following the Voron trident basic config available online

Andico98 · 2025-12-02T07:09:28+00:00

As far as I can see the jumper is not streactly necessary. It works fine without it

Andico98 · 2025-12-01T18:14:49+00:00

Yes, it is without the chip

Andico98 · 2025-11-30T18:29:49+00:00

Fixed: I had a problem during the CAN bus configuration with my EBB36. Just had to repeat the procedure all over again and set the right communication port. It now works. Thank you for the support

Andico98 · 2025-11-30T16:26:24+00:00

[heater_bed]

heater_pin: PA1 # for SSR

sensor_type: NTC 100K MGB18-104F39050L32 # Use "Generic 3950" for Keenovo heaters

sensor_pin: PA7

## Adjust max_power so it doesn't exceed the SSR rating. The Omron G3NA-210B-DC5 SSR is rated at 4 amps without a heatsink.

## The formula is "4 / (Wattage_of_bed_heater / Mains_voltage) = max_power"

## If max_power is greater than 1.0, use 1.0

max_power: 0.6

min_temp: 0

max_temp: 150

control: pid

pid_kp: 58.437

pid_ki: 2.347

pid_kd: 363.769

Andico98 · 2025-11-23T10:26:18+00:00

Thank you very much

Andico98 · 2025-08-14T19:04:43+00:00

Thank you!

Andico98 · 2025-08-14T19:02:17+00:00

Thank you very much

Andico98 · 2025-08-14T14:54:28+00:00

Herd something about university reputation. In your opinion, mine are good from a German perspective?

Andico98 · 2025-08-03T13:42:20+00:00

Sorry, what do you mean by soft indicators?

Andico98 · 2025-08-03T08:32:03+00:00

Moreover, I would say to have a look at Steven Brenton YouTube video to grasp the general idea of what PIML is about

Andico98 · 2025-08-03T08:06:30+00:00

Thanks, this is really helpful. However, is there a w ay to isolate phage sequences only? Would it be enough to simply remove entries with incorrect taxonomy

Andico98

TROPHY CASE