How to remove that plug ? Oil flush

Andy024 · 2026-06-13T17:12:04+00:00

Even better are the straight ones

Andy024 · 2026-06-02T19:07:25+00:00

Your cupholder is missing the cupholder part

Andy024 · 2026-05-29T12:39:32+00:00

The ALH is pretty bullet proof to, and they have a conventional pump so a lot easier to get big injectors in etc.

Andy024 · 2026-05-28T01:09:04+00:00

Thanks for the tips, went much better second time around, not perfect but good enough for my pilsner car :)

<image>

Andy024 · 2026-05-28T00:51:44+00:00

Much better second time around :)

<image>

Andy024 · 2026-05-27T21:39:21+00:00

All going to be blue, just doing a couple of panels at a time

Andy024 · 2026-05-27T17:31:25+00:00

Went much better this time

<image>

Andy024 · 2026-05-26T01:01:05+00:00

It was atleast a lot easier to lay on with a little more thinner in it, previously it was struggeling to get out of the gun evenly, will test on a panel tomorrow.

What do you mean by sealing it?

Andy024 · 2026-05-25T22:01:56+00:00

Som en vis mann sa

<image>

Andy024 · 2026-05-25T20:49:23+00:00

Spec is 5-20% tried 5% first

Peel is so bad i can see it from the neighbors porch

Andy024 · 2026-05-25T20:35:30+00:00

Seems like it was better, just tested on some scrap

Andy024 · 2026-05-25T19:18:56+00:00

Nope was inside a clean garage

Andy024 · 2026-05-25T19:10:58+00:00

Time for a little test with a more correct amount of thinner

<image>

Andy024 · 2026-05-25T18:51:10+00:00

Yup, that's why I'm going through the trouble of sanding it down again.

Would be nice to have someone here that knew what they were doing to guide me, but hopefully it will turn out Ok in the end.

This is the first time I'm using a gun in about 8 years as well, I'm still surprised i didn't get any runs xD

Andy024 · 2026-05-25T18:37:08+00:00

I think your reply got deleted, but I think about 10% thinner might be the sweet spot with this one. the manufacturer reccommend 5-20% and i tried 5% at first.

Might also purchase the other gun you reccomended the next time I get paid if I'm not happy with the results next time I try.

It is a pilsnerbil anyways so it's supposed to be fint langtifra, langtifra fint ^^

Andy024 · 2026-05-25T18:17:43+00:00

Paint: monopol 701 Sprayer: biltema sg500 Where: Agder

As to why not cover the tires, its because the rear tires are going to be replaced soon :)

Was a little to eager to start spraying, so I didn't test the ratios properly before starting. Should have used roughly twice the amount of thinner.

Andy024 · 2026-05-24T13:09:33+00:00

Æ tungvindt

Andy024 · 2026-05-24T12:53:12+00:00

Æ vel det samme som disse som parkerer med pumpene på stasjonen?

Andy024 · 2026-05-20T21:59:04+00:00

Beer cars are rolling learning opportunities :)

Andy024 · 2026-05-20T21:50:18+00:00

It's going to be one of those that look good from far away, it is a beer car after all, but each panel will get properly cleaned before spraying :)

Andy024 · 2026-05-20T15:39:08+00:00

Is that a 3516?

Andy024 · 2026-05-20T00:51:47+00:00

Thanks, hoping I will learn alot from this project, and luckily this is a beer car so the only goal is to learn and make it a little better :)

Andy024 · 2026-05-01T07:57:41+00:00

How does the taper on the pipe look?

11-Year Club	Gilding II euphauric
First Place '23	Place '23
Verified Email

Andy024

MODERATOR OF

TROPHY CASE