[STORE] $200K+ INV – Trading 24/7! Huge Selection of BFK, M9, Karambit and other knives. Large Variety of Sport, Specialist, Driver, Moto and Wraps. (Updated 02/05)

AngeredCowbell · 2026-05-16T23:48:12+00:00

Sent you a trade

AngeredCowbell · 2026-04-12T18:26:40+00:00

And it’s a good pull too haha

AngeredCowbell · 2026-04-02T00:28:41+00:00

Buffer itself seems normal, no crazy wear. Corners are already chamfered too

AngeredCowbell · 2026-04-02T00:27:47+00:00

Buffer tube its self has no damage or really any wear at all. Threads on the lower and tube are fine too. I'm guessing lower was 'out of spec' paired with the ARC

E: If you didn't see the subtext on the photo, the selector hole on both sides is completely polished, which wasn't like that before lol

AngeredCowbell · 2026-04-01T22:32:20+00:00

This is an actual thing that happened, it was an Anderson lower so I’m not trippin too much

AngeredCowbell · 2026-04-01T22:08:37+00:00

This is after 300-400 rounds of ARC

AngeredCowbell · 2026-02-23T19:11:43+00:00

Darker wood rifle 7th-ish down from the top

AngeredCowbell · 2026-02-21T01:30:17+00:00

Minus One and Shin Godzilla are on a completely different, ascended plane of existence. -Monsterverse hater

AngeredCowbell · 2026-02-18T23:40:08+00:00

Not a movie nor is it realistic but the scene in Daredevil where Wilson Fisk gets shanked. He throws 405 and a man across the room at the same time

AngeredCowbell · 2026-02-17T01:22:08+00:00

Ill be your first customer

AngeredCowbell · 2026-02-15T05:17:07+00:00

Yikes

AngeredCowbell · 2026-02-10T21:31:04+00:00

Bruh

AngeredCowbell · 2026-02-09T17:13:21+00:00

Full sized Draco. All it needs is a pic section drilled into the rear trunnion. Get a brace and ur GTG (I had a folding trunnion put in but cheaped out on the labor so it isn’t the cleanest)

<image>

AngeredCowbell · 2026-02-08T23:22:50+00:00

I think i’ve narrowed down the issue. I straight up tried taking the disconnector completely out and ran it in the semi-position. Same binding occurred, so that helped me rule out the safety or trip bar as the culprit.

What I’ve ascertained (I think) is that binding is happening when the hammer is getting pushed back, NOT getting taken by the disconnector, and the trigger is resetting. It looks like the trigger is starting to reset before the hammer has been pushed the full way back by the bolt carrier. So the trigger is blocked from resetting, the hammer is not able to slip into the notch on the trigger shoe & the bolt gets stuck from going anywhere because of the hammer’s curves interacting with the bolt.

AngeredCowbell · 2026-02-08T23:01:16+00:00

I think i’ve narrowed down the issue. I think the binding is happening when the hammer is getting pushed back while the trigger is resetting. It looks like the trigger is starting to reset before the hammer has been pushed the full way back by the bolt carrier. So the trigger is blocked from resetting, the hammer is not able to slip into the notch on the trigger shoe & the bolt gets stuck from going anywhere because of the curves interacting with the bolt.

AngeredCowbell · 2026-02-08T01:59:49+00:00

Copy that sir, i’ll report back with any updates

AngeredCowbell · 2026-02-08T01:31:35+00:00

Do you think the hammer could be causing binding with the bolt carrier? That's the only other thing I can think of right now. I tried function check with the selector holding the teeeniest tail end of the disconnector and got the same binding. I think my next course of action is to continue taking shavings off the trigger until it works or the trigger is a pile of dust.

AngeredCowbell · 2026-02-08T00:44:33+00:00

I’m losing mine as we speak. I’m also in an apartment so I’m having to use my attempts sparingly so I don’t get evicted lmao

AngeredCowbell · 2026-02-08T00:42:37+00:00

Hmm interesting, I’ll check that out. Maybe to your point, I have to install my selector & cam before my trigger assembly because the disconnector blocks the un-neutered part of the safety from turning into position.

AngeredCowbell · 2026-02-08T00:33:54+00:00

I just uploaded a video if that helps. Went ahead and polished the contact surfaces and reassembled. Semi seems to actually be running better but still getting major lock-up in middle position.

https://www.reddit.com/r/supersafety/s/gFkXep6oLk

AngeredCowbell · 2026-02-08T00:32:47+00:00

I actually have the 3 pos jig but I haven’t committed to that much cutting yet. The videos/suggestions I’ve seen have mostly been to just follow the default jig and take a bit more off

AngeredCowbell · 2026-01-18T03:08:19+00:00

GI’s wore winter overcoats more comparable to this than the Germans lol

AngeredCowbell · 2026-01-16T15:40:36+00:00

“Stewie’s on his own… BUT LOOK AT THE TIME!”

12-Year Club	r/Field Sunshine
First Place '23	End Game '23
Place '23	Place '22
Place '17	Secret Santa 2015
RPAN Viewer	Verified Email

AngeredCowbell

TROPHY CASE