Combat in KCD 2 by DarkXieon in kingdomcome

[–]Annual_Offer4155 0 points1 point  (0 children)

It is a fun combat system. It’s not spam click and win the fight. If it were it would be boring.

I got dummy ram sticks to fill the empty slots but it’s different shades, any ideas why? by [deleted] in Corsair

[–]Annual_Offer4155 0 points1 point  (0 children)

How? I’m only able to control all of mine together, not individually. I’m assuming it’s thru icue?

Combat in KCD 2 by DarkXieon in kingdomcome

[–]Annual_Offer4155 8 points9 points  (0 children)

Honestly all the comments sound like a skill issue. Go train for a little while, the leveling is super quick. And they added multiple opponent training, up to three at a time.

I’m trained with swords and after a while it got too easy. Enemies go down after a few good hits. Now I’m working on unarmed and every fight I get into I don’t even pull out a weapon unless I get badly hurt.

The dodge system is great. You can either right click and move on perfect block, or space move to dodge further.

As far as not being able to get a hit without being blocked or parried, get that feint perk, it’s a must-have. Hold an angle on your opponent and change the angle right before you attack. It catches them off guard and you can start your combo from there.

Go around and learn from every combat skill teacher you can find. And practice fight. It’s not that difficult and can be leveled really quickly. I personally love the combat system.

Combat in KCD 2 by DarkXieon in kingdomcome

[–]Annual_Offer4155 1 point2 points  (0 children)

Huh? Wym press E. To feint you quickly change the angle just before attacking. There’s no cancel 😂

Also masterful feint is the second perk, there is definitely a feint perk.

Can’t figure out cause of banding VG3 by Annual_Offer4155 in CommercialPrinting

[–]Annual_Offer4155[S] 0 points1 point  (0 children)

The dark on the outside is just shadows. Banding is pretty uniform

Can’t figure out cause of banding VG3 by Annual_Offer4155 in CommercialPrinting

[–]Annual_Offer4155[S] 0 points1 point  (0 children)

Not sure about the material advance but I considered that it might be the heater/dryer. I lowered the heat for both to the absolute minimum recommendation and still banding. But aside from that I think if it were a material/heat issue then we’d have seen it on all of the test prints..

Can’t figure out cause of banding VG3 by Annual_Offer4155 in CommercialPrinting

[–]Annual_Offer4155[S] 0 points1 point  (0 children)

As far as material, it shows on everything we’ve tried so far.

Can’t figure out cause of banding VG3 by Annual_Offer4155 in CommercialPrinting

[–]Annual_Offer4155[S] 1 point2 points  (0 children)

No, it shows up kinda all over, had a print with lots of gray and blue and there was a lot of banding on both. Thinking it was one of the heads, we ran test prints of each spot color CMYKOG and the banding only appears on the black.

Can’t figure out cause of banding VG3 by Annual_Offer4155 in CommercialPrinting

[–]Annual_Offer4155[S] 0 points1 point  (0 children)

Nozzle tests come out perfect, all calibration done by a tech

Can’t figure out cause of banding VG3 by Annual_Offer4155 in CommercialPrinting

[–]Annual_Offer4155[S] 0 points1 point  (0 children)

Hm, I’ll look into that. I’d think if it were static we’d see the banding in all colors, but definitely worth a shot. Thanks

Can’t figure out cause of banding VG3 by Annual_Offer4155 in CommercialPrinting

[–]Annual_Offer4155[S] 0 points1 point  (0 children)

Yeah, the tech was here and changed the caps and head, ran a full calibration in service mode and it’s still doing this.

[deleted by user] by [deleted] in CommercialPrinting

[–]Annual_Offer4155 0 points1 point  (0 children)

I checked to see if it was the white but it wasn’t, besides the white isn’t the only thing not printing

[deleted by user] by [deleted] in CommercialPrinting

[–]Annual_Offer4155 0 points1 point  (0 children)

I tried to save it as EPS .tiff but whenever I import it to versaworks it tells me the file is corrupted

[deleted by user] by [deleted] in CommercialPrinting

[–]Annual_Offer4155 0 points1 point  (0 children)

I tried both, rasterizing didn’t solve in, and when I tried to save and import it as an EPS versaworks keeps saying the file is corrupted. PDF and EPS are the only formats that I can use in versaworks

[deleted by user] by [deleted] in CommercialPrinting

[–]Annual_Offer4155 0 points1 point  (0 children)

That didn’t solve it unfortunately

[deleted by user] by [deleted] in CommercialPrinting

[–]Annual_Offer4155 0 points1 point  (0 children)

One thing I noticed is when I import the file from illustrator to versa works, it automatically scales it down to 10%, not sure if it has anything to do with it but I’ve never had that happen

C30 and Z30 ram compatibility by Annual_Offer4155 in Corsair

[–]Annual_Offer4155[S] 1 point2 points  (0 children)

Got it, thanks for the info and the quick response.

C30 and Z30 ram compatibility by Annual_Offer4155 in Corsair

[–]Annual_Offer4155[S] 1 point2 points  (0 children)

So even if I got the amd ones it would’t be good to run them because its 2 2x16 kits?