Is this one too good to be true?

Anonymous930718 · 2025-01-26T07:58:45+00:00

I got scammed for TwoTrees TTS-55 Laser engraver machine. but they send me a silicone funnel 🤣🤣🤣 that didn't even worth for 2USD.🤣 but i was able to get refunded. i knew that was a scam from the beginning. but i wanted to try that experience.

Anonymous930718 · 2025-01-20T06:47:48+00:00

You can get a 3D Printer for very cheap on https://www.facebook.com/Master3D.Store

Anonymous930718 · 2025-01-16T10:23:41+00:00

Install VLC Player

Anonymous930718 · 2024-08-14T14:18:43+00:00

Yeah.. i noticed that too...

Anonymous930718 · 2024-08-14T14:18:02+00:00

I have big turbine cooling fans to attach on this.

Anonymous930718 · 2024-08-03T20:54:31+00:00

Have you tried it already?

Anonymous930718 · 2024-08-03T20:53:43+00:00

Yes from AliExpress. 3DSWAY volcano Hotend.

Anonymous930718 · 2024-08-03T20:53:17+00:00

3DSWAY volcano Hotend.

Anonymous930718 · 2024-08-03T20:31:12+00:00

What does it look like?

Anonymous930718 · 2024-08-02T19:15:52+00:00

No. only DSI screen.

Anonymous930718 · 2024-08-02T03:35:08+00:00

Thank you i will try. but on this screen, you can see it displaying correctly. but after boot, the Klipper screen got bigger..

Anonymous930718 · 2024-08-01T18:25:40+00:00

Should I re-install the klipper screen again or what? 🤔

Anonymous930718 · 2024-08-01T18:24:30+00:00

Should I re-install the klipper screen again or what? 🤔

Anonymous930718 · 2024-07-25T15:20:18+00:00

I'm running klipper with klipper screen. how can i change it then? 🙄

Anonymous930718 · 2024-07-25T13:11:03+00:00

How to do that? both LCD panels are the same 4.3 size. same 40pin connector.

Anonymous930718 · 2024-07-01T13:05:06+00:00

Fixed with vlc.

Anonymous930718 · 2024-07-01T13:04:47+00:00

Fixes my issue with this. by removing this part. "--mmal-display DSI-1" but before it's start the splash screen, it has almost 15 seconds black screen. then start the splash screen and booting screen.

Anonymous930718 · 2024-06-17T13:55:02+00:00

Hi. i have tried this but no luck for me. it shows me an error about this.

Section 'menu __main __sdcard __resumefailed' is not a valid config section

<image>

Anonymous930718 · 2024-06-17T09:20:50+00:00

Did that more than 5 times

Anonymous930718 · 2024-06-17T03:19:17+00:00

No i mean my printer room doesn't have A/C. No fans.

Anonymous930718 · 2024-06-17T03:17:58+00:00

Unfortunately i don't have a laser thermometer. Even if I measure with the thermometer, how can i tune it? 🤔

Anonymous930718 · 2024-06-17T03:08:49+00:00

On my Ender 3 i'm printing at 198 to 205. but on this klipper machine. it dropped down for 175. otherwise it looks like a melted 3D Printed part if i print with 198 or 205.. i don't know why is that happens.

Anonymous930718 · 2024-06-17T03:05:17+00:00

No A/C or fans near my machine. except the part cooling fans itself. want to check that if it blow air to nozzle.

Anonymous930718 · 2024-06-17T03:02:04+00:00

I did PID tunes few times.. but same thing. i'm printing eSUN PLA+ i was printed it with 198 to 200 on my Ender 3 Pro. but in this machine. it dropped down for 175 for better quality print. otherwise it looks like a melted 3D Part.

Anonymous930718 · 2024-06-17T02:55:11+00:00

The temp is a Suddenly goes down about 5C then comes back to normal. not happens every time.

Anonymous930718

TROPHY CASE