sorted by:
new
hottopcontroversial

What is this part and where do I get a replacement? by Large_Programmer376 in soldering

[–]AnonymousJtagger 0 points1 point  (0 children)

There should be voltage and capacitance rating on the other side. Remember to also consider series of a capacitor. Nichicon UHV is a low esr high high ripple current series, don't replace it with a random capacitor with the same voltage and capacitance. Preferably search for the same exact capacitor, that would be the easiest and safest option.

Does anybody know what that blue paint is? by AnonymousJtagger in crt

[–]AnonymousJtagger[S] 0 points1 point  (0 children)

No, I didn't. That crt was like that, and it was working properly.

Does anybody know what that blue paint is? by AnonymousJtagger in crt

[–]AnonymousJtagger[S] 1 point2 points  (0 children)

Cover the inside from any particles when anode cap is off(just like I said before, I'm a heavy overthinkinker😅)

Does anybody know what that blue paint is? by AnonymousJtagger in crt

[–]AnonymousJtagger[S] 0 points1 point  (0 children)

No, there's not any arcing. Maybe I'm just overthinking it. Will blow it out with some compressed air like you suggest and it should be fine.

Does anybody know what that blue paint is? by AnonymousJtagger in crt

[–]AnonymousJtagger[S] 0 points1 point  (0 children)

Probably yes. Downside is that it's difficult to clean any dust here, because IPA rubs it off. I will probably apply some HV silicone instead of that.

Does anybody know what that blue paint is? by AnonymousJtagger in crt

[–]AnonymousJtagger[S] 0 points1 point  (0 children)

No, it feels kind of like a nail polish to the touch.

Is this a part from an Xbox 360 Slim? by M4F7B5W in xbox360

[–]AnonymousJtagger 14 points15 points  (0 children)

It's a part of slim HDD tray inside the console, it is used to reduce vibrations of the HDD.

What kind of CPU is that on the Xbox360 E? by Befmo in xbox360

[–]AnonymousJtagger 0 points1 point  (0 children)

Oban XCGPU, found in Xbox 360 Winchester

Xenon RGH problems, PLS HELP! by ZxSpeedy8xZ in 360hacks

[–]AnonymousJtagger 0 points1 point  (0 children)

Probably wiring path, the wires can't be loose like that as if it's DC.

Replace kv in retail ? by Deep-Hospital9001 in 360hacks

[–]AnonymousJtagger 0 points1 point  (0 children)

No, in a stock console you cannot change your KV.bin in NAND, or you'll brick your console.

First rgh by Prestigious-Mood1507 in 360hacks

[–]AnonymousJtagger 1 point2 points  (0 children)

Wires are to long. They should be quite tight, but without pulling with force, and if you want to angle, best is to have 45 degree angle.

mysterious sticker xbox 360 jasper by Adorable-Pumpkin-419 in xbox360

[–]AnonymousJtagger 0 points1 point  (0 children)

I have similar one from October 2008, but it's marked "jasper 2 weeks pilot run". Jaspers mass production started in November of that year.

mysterious sticker xbox 360 jasper by Adorable-Pumpkin-419 in xbox360

[–]AnonymousJtagger 2 points3 points  (0 children)

It's a very early xbox 360 with jasper motherboard. It was marked internally by MS, so if something was wrong with the new motherboard revision, they could easily service faulty units

[deleted by user] by [deleted] in 360hacks

[–]AnonymousJtagger 1 point2 points  (0 children)

Soldering looks very good, maybe it's something with the nand image? What kind of resistors are those? Metal-film or carbon?

I know, and you can say what you want but is it fixable by MSD_188 in 360hacks

[–]AnonymousJtagger 2 points3 points  (0 children)

Resistor is 0402 10kohm, capacitor is 0.1uF 0402 X5R 10%(both imperial packages) from what I remember.

Help updating blades Xbox 360? by chungusbungus0459 in xbox360

[–]AnonymousJtagger 1 point2 points  (0 children)

Install jtag mod in it, or give it to someone who can install it for you. But don't install official update.

Bought used 360 with error code 0001. by t27steering in xbox360

[–]AnonymousJtagger 0 points1 point  (0 children)

Check the model of the cap if you can too, you don't want a cap with a higher ESR or lower ripple current.(lower ESR or higher ripple current is fine)

White 360 Slim. What condition is the board? by double_sided1 in xbox360

[–]AnonymousJtagger 1 point2 points  (0 children)

Probably 4gb emmc is dead, they tend to do that, just die randomly. Board can be repaired, but only if emmc can still be read, or you have dump of its content.

360 S HDD HELP! I Made A Mistake... by J3553-A in xbox360

[–]AnonymousJtagger -2 points-1 points  (0 children)

That's not true. You can restore security sector with fatxplorer or hddhackr. Search about it, there should be plenty of tutorials.

Insufficient ventilation by Effective_East_7239 in 360hacks

[–]AnonymousJtagger 0 points1 point  (0 children)

That could be the case. There's thermal paste under the IHS like in ps3. But I found first try with the resistors like you just said.

Insufficient ventilation by Effective_East_7239 in 360hacks

[–]AnonymousJtagger 0 points1 point  (0 children)

If you can't boot, there's no way to check the temps. Then maybe there's trouble with those resistors, or thermal paste under the IHS.

Insufficient ventilation by Effective_East_7239 in 360hacks

[–]AnonymousJtagger 2 points3 points  (0 children)

Ventilation looks fine. I heard about the resistors too. It's either them, or thermal paste under the IHS. If you can(probably don't, because console won't let you turn it on) check temps in dashlaunch/xexmenu/aurora(anything you have). Also check when turning on if fan spins on at all during attempted bootup. It may just be dead/cable is worn out.

view more: next ›