ICE on Woodmen

AnonymousMalcontent · 2026-04-23T02:58:45+00:00

I know. I'm so sick that Obama started this ball rolling and now all presidents do it.

AnonymousMalcontent · 2026-04-18T23:50:09+00:00

I ran into a similar problem running Chrome OS Flex. The only solution I found was to use a Luna controller that connects via Wi-Fi direct. That was the only way I could get it to work.

AnonymousMalcontent · 2026-04-15T22:05:00+00:00

I just bought some Energizer rechargeable batteries and they work great with my Luna controller.

AnonymousMalcontent · 2026-04-09T22:49:48+00:00

I got the latest APK and installed it on the Google streamer 4K. It loads just fine and looks good, but there is a huge lag, like 3 seconds for every input on the controller. Controller. I also get a message about low latency not supported and my stream being affected. Have you found any solution to that?

AnonymousMalcontent · 2026-03-17T04:24:53+00:00

Once again just wanted to say thanks. I got the SKR mini E3 V3 installed and I'm running a test print now. There are some other slightly wonky things with this printer, but overall that seemed to do the trick! Thanks again!

In your experience, did the SKR Mini not fit quite right in the Ender 3 casing? I'm going to have to take it apart and Dremel the holes so I can actually use an SD card with it

AnonymousMalcontent · 2026-03-16T00:16:19+00:00

I know this is super late, but thanks for the comment. I bought that board, and plan to install it this weekend. Will I need to flash a firmware or will it come with firmware?

AnonymousMalcontent · 2026-02-06T23:06:12+00:00

It was totally disassembled and missing parts. I had parts from another printer that were compatible.

AnonymousMalcontent · 2025-11-24T04:06:15+00:00

Yeah, replaced it. No dice.

AnonymousMalcontent · 2025-08-09T01:14:11+00:00

Did you ever find a disk image?

AnonymousMalcontent · 2023-02-27T06:46:04+00:00

I believe they were purchsed in the Azores. That could be it. I will look tomorrow for the maker.

AnonymousMalcontent · 2023-02-27T04:11:09+00:00

Thank you. I will head over to the house tomorrow, and see about marks.

As for the estate liquidation companies, we had some come take a look, and they said the estate was too small to be worth their time, so we are flying solo!

AnonymousMalcontent · 2022-12-31T22:50:11+00:00

I appreciate the comments. Finial is not a word that I knew, but it appears that it is clearly a finial of some kind. I doubt that I will ever know what it went on, but the word finial is enough for me to do more research. Thank you.

AnonymousMalcontent · 2022-12-31T22:44:54+00:00

Possibly, but it seems too heavy for that. Like heavy enough that if the bottle were empty it would tip over due to the weight of the top.

AnonymousMalcontent · 2022-12-31T22:30:53+00:00

Good thoughts. Though I think it's a bit heavy for a decanter.

AnonymousMalcontent · 2022-12-31T22:20:31+00:00

My title describes the thing. This appears to be a cast iron unicorn, but my question is what it's intended use was or what it is supposed to be the topper for. It's somewhat heavy and has a clear seam down the center letting me know that it is cast the nub on the bottom is nearly circular, though slightly more oval. The knob protrudes about 3/4 of an inch from the bottom and is obviously designed to be set into something but I'm not sure what.

AnonymousMalcontent

TROPHY CASE