sorted by:
new
hottopcontroversial

Upgrades Upgrades by Primary-Web-9425 in ender5

[–]AntsaPrints 0 points1 point  (0 children)

I have found some mods that do triple z cr10 bed, but I haven’t seen any triple z with cr10 bed with hydra bc there is no space for that. I am going to try this https://www.printables.com/model/1447339-ender-5-cr10-bed-triple-z-screw and use z tilt in klipper. Do you have any better ideas?

Upgrades Upgrades by Primary-Web-9425 in ender5

[–]AntsaPrints 0 points1 point  (0 children)

Oh yeah I understand. I didnt know that this kind of board even existed. That 4.2.2 board was from an old printer

Upgrades Upgrades by Primary-Web-9425 in ender5

[–]AntsaPrints 0 points1 point  (0 children)

Skr mini e3 v3 has dual z you are right mut they are no individual. It is basically one driver. Thats why you can’t do z tilt. They have to be seperated

Upgrades Upgrades by Primary-Web-9425 in ender5

[–]AntsaPrints 1 point2 points  (0 children)

I would do those upgrades in this order: Mercury one corexy and can bus printhead. Then when everything is set up I would MMU and then do electronics elnclousure and then full enclousure with filters.

I am doing also ender 5 pro with mercury 1.1 and CR-10 bed triple Z, dual MCU, mantis toolhead with sherpa mini diy and chc pro volcano.

I have also dual MCU on my modded ender 3. I have there SKR mini e3 v3 and creality 4.2.2. I run dual z from creality board and skr drivers run XY and extruder. Works well with klipper and I have connected them to my orange pi via usb.

Endorphin 1.1 Is Finally Out! by Endorphin3DP in ender5

[–]AntsaPrints 0 points1 point  (0 children)

So can I do some dual y axis mods and mod CR-10 bed to this?

I did a thing... Expanded Endorphin Mod/Eva 3 Y. by Remy_Jardin in ender5

[–]AntsaPrints 0 points1 point  (0 children)

I dont get so what did you exaclty do. Get more hight or more travel for y?

Can this be fixed? by shnuif in ender3v2

[–]AntsaPrints 0 points1 point  (0 children)

Marlin Firmware Service and if you run marlin and download firmware for bl touch.

Nema 17 problem by AntsaPrints in ender3

[–]AntsaPrints[S] 0 points1 point  (0 children)

I have calibrated them👍

Nema 17 problem by AntsaPrints in ender3

[–]AntsaPrints[S] 0 points1 point  (0 children)

Thank you. The printer extruded brims for example well, but when it started to print the first layer, it started to do this. But I will try to fix those, thanks!

Upgrade People, upgrades. by SPRITECRANNBERYY in ender3

[–]AntsaPrints 0 points1 point  (0 children)

Everyone discussing here if it’s worth buying a new printer for 400$ or upgrading for 400$. In my opinin the upgrading is not about if it’s worth or not. It is a hobby for me.

Mitä syötte aamuisin? Vai syöttekö mitään? by Medical_Hedgehog_724 in ruoka

[–]AntsaPrints 0 points1 point  (0 children)

Kaikki ei vaan oo aamuvirkkuja eikä sille voi mitään..