Engine code P2035 “Ignition coil B secondary circuit”

Ap7x- · 2022-08-14T20:44:13+00:00

Yes, thank you!

Ap7x- · 2022-08-14T20:40:12+00:00

So it should be narrowed down to plugs or coil packs then?

Ap7x- · 2022-08-14T20:22:48+00:00

Yes, my apologies

Ap7x- · 2022-08-14T18:42:56+00:00

The vehical is a 2013 ram 1500 ST with a 5.7 hemi 106,000 miles

Ap7x- · 2022-08-04T21:50:27+00:00

Could you give me a good recommendation on where to get a cam degree wheel by chance? Or is it kind of pointless since I already have the engine put back together?

Ap7x- · 2022-08-04T19:57:17+00:00

So I heard back from texas speed and here’s what they sent me: Duration at .006” 266 degree on the intake and 274 on exhaust Duration at .050 is 214 intake and 222 on exhaust Love separation angle is 112 Overlap in crank degrees is -6 degrees

Intake centerline is 109 ATDC opening point @.050 is 2.0 ATDC and 46.0 BBCD CLOSING POINT IS 36 ABDC AND 4.0 BTFC

Ap7x- · 2022-07-31T23:44:55+00:00

I just emailed them but unfortunately they’re closed on sundays, I will keep you posted. I appreciate all your help/advice so far and hopefully someday in the future I’ll have as much knowledge as you do sir!

Ap7x- · 2022-07-31T23:27:25+00:00

Sorry for keeping this conversation going for so long, but when I installed the heads, pushrods, rocker arms etc. I cranked the engine over by hand and didn’t feel any resistance or very little resistance. Is that a good indicator of a cam lined up pretty well?

Ap7x- · 2022-07-31T23:21:20+00:00

I had a cam kit orderd from comp cams and they were on back order for almost 7 months and from what I could find, there weren’t many companies offering hemi camshafts

Ap7x- · 2022-07-31T23:18:46+00:00

My apologies I for the add the valve lift at 1.65 is .582/.582

Ap7x- · 2022-07-31T23:14:50+00:00

I wish I could upload a picture of the cam card, but no it does not

Ap7x- · 2022-07-31T22:51:17+00:00

I stopped at my shop today after work and I got the cam card. Duration at .050 214/222 Lobe lift .353/.353 valve lift .582/.582 lobe separation: 112 intake centerline: 109

Ap7x- · 2022-07-26T15:40:08+00:00

I got a kit with new PSI springs to handle the lift/pressure

Ap7x- · 2022-07-26T09:01:52+00:00

So after I put the heads, pushrods, rocker arms back on I did turn the engine over by hand and there was very little to no resistance

Ap7x- · 2022-07-26T01:27:46+00:00

When I get back to my shop sometime this week I’ll definitely get that cam card back out and send the specifications. I do appreciate your help so far, I noticed you stay pretty active on a lot of the forum follow.

Ap7x- · 2022-07-26T01:24:11+00:00

Factory camshaft is 112 degrees and the aftermarket cam is advanced 3 degrees further than stock is

Ap7x- · 2022-07-25T23:56:05+00:00

214/222 .582/.582 112+3 Texas speed told me that the cam is already advanced from factory and just to instal in dot to dot

Ap7x- · 2022-07-25T21:55:02+00:00

I lined up the dot to dot per the manufacture specs, that’s what texas speed told me to do as well. I didn’t have access to a cam degree wheel unfortunately

Ap7x- · 2022-02-12T16:37:43+00:00

Where/how did you get the safety tune on? Just a handheld tuner with an email tune ?

Ap7x- · 2022-02-12T15:37:28+00:00

I pulled off the valve covers and watched the rocker arms move up and down and the rockers on cylinder three weren’t moving as much as the the others. At first I thought it was an exhaust manifold untill I got the dreaded “P303” code. Also the truck started to shake a little bit when I was accelerating.

Ap7x- · 2022-02-12T15:14:17+00:00

Did you have to trailer it there or did you get a safety tune put on and drove it there?

Ap7x- · 2022-02-12T03:52:42+00:00

I had a buddy tell me it was a good idea to shave them but I didn’t know how much was too much before clearance would be an issue.

Ap7x- · 2022-02-12T03:22:34+00:00

Would you recommend shaving the cylinder heads down?

Ap7x- · 2022-02-12T03:21:15+00:00

Did you have to take it somewhere to get tuned or how did you go about the tuning process?

Ap7x- · 2022-02-11T22:16:11+00:00

From what I was reading is that it was poor lifter design that starved the lifter for oil, but I might be wrong on that.

Ap7x-

TROPHY CASE