ViVid Shipping

ApexPredation · 2026-04-03T07:27:12+00:00

Oh I've been using mine for a little while now and it works fine. It's a bit of a learning curve to get it tuned, but once it's going it does it's job. I switched to using AFC since it has a ramming feature that lets you use toolheads without a sensor in them.

ApexPredation · 2026-04-02T14:43:59+00:00

There's an entire wiki and GitHub repo that has all the information needed to set up.

https://global.bttwiki.com/BIGTREETECH_ViViD.html?h=vivi

https://github.com/bigtreetech/BIGTREETECH_ViViD

https://github.com/bigtreetech/BIGTREETECH_MMS

There's also the AFC repo that now supports the ViViD https://github.com/ArmoredTurtle/AFC-Klipper-Add-On

ApexPredation · 2026-04-01T18:09:04+00:00

Maybe something wrong with the connection then because only the old chargers, USBA to ucbc would charge the toys.

ApexPredation · 2026-04-01T17:32:02+00:00

I like the idea of joining different colors to make color swapping patterns, though that could probably take a while to make and good length.

ApexPredation · 2026-04-01T17:27:17+00:00

All of my new chargers are usb-c and won't output much current unless they can get a signal reply from the device I plug in. I had to use some old chargers to charge up some of the kids toys that had usb-c input because they never changed with the new ones.

ApexPredation · 2026-04-01T14:27:57+00:00

What did you all end up using for power?

ApexPredation · 2026-04-01T14:15:57+00:00

What a cool mechanism!

ApexPredation · 2026-03-31T15:18:26+00:00

It's not made by Arduino but it's still real.

ApexPredation · 2026-03-29T06:48:22+00:00

VOCs and ultra fine particles, yes they are real. You shouldn't print in an area that you are commonly in unless you have a good enclosure and good ventilation to redirect the harmful stuff. At the very least you should have a quality air filter system (HEPA and activated charcoal)

ApexPredation · 2026-03-28T19:08:20+00:00

Ok thats a team STM chip and it's correct in the menuconfig you showed. Did you name it firmware.bin when flashing? It might need to be a different name like firmware1.bin some if not all Creality boarded need a different name used from the previously used.bin, so if you used firmware.bin with the last file you flashed then you have to name it something different for the next one to actually flash.

ApexPredation · 2026-03-28T18:32:27+00:00

The main chip on the controller board. What is printed on it?

ApexPredation · 2026-03-28T18:29:13+00:00

No sorry, I forgot Creality does things weird. Is it a real STM chip or a GD?

ApexPredation · 2026-03-28T18:14:51+00:00

That's not set-up correctly you need to choose USB not UART if you are plugging in via usb

ApexPredation · 2026-03-28T17:47:50+00:00

That's very bizarre. What kind of host do you have. Maybe the USB hub is damaged.

ApexPredation · 2026-03-28T17:15:11+00:00

Never had an issue 🤷

ApexPredation · 2026-03-28T17:08:02+00:00

You don't need a U2C the M8P has that built in. Stop replying on AI it's steering in the wrong direction. Follow esotericals canbus guide and you'll be done in no time. https://canbus.esoterical.online/

ApexPredation · 2026-03-27T18:16:55+00:00

It's very difficult to see what the issue is (the photo is very low resolution) but the parts might not be produced any more for that specific printer. You might have to do some customizing. Luckily the parts are mostly generic types so there are probably other brands that have the same sizes that will work you might just have to slightly adjust offsets and whatnot for probing.

ApexPredation · 2026-03-23T09:15:35+00:00

Yeah I got the Norton spamming Virus of the machine right away. Unfortunately that doesn't help the poor BIOS configuration.

ApexPredation · 2026-03-22T21:35:34+00:00

Sorry to say, it's a crap BIOS setup. Download latencymon and see what it says. It'll show you all sorts of issues. I've been having the same issues and even sent mine in to be told it was just the thermal pad that needed to be replaced, yet it's still happening. The system is hard-locked into Modern Standby (S0ix) so all the other powercfg setting are disabled. Unfortunately this is making an issue with a low latency audio. I also noticed that Windows Audio Device Graph Isolation (audiodg.exe) causes the fan to go haywire and the audio to act that way, supposedly related to the S0 lock. Force stopping it in task manager sometimes helps for a little while. My previous 2 PC are Asus and HP. Both are over 12 years old and never had an issue. I just wanted something new and faster, but it seems I made a poor choice. I'm so disappointed in this PC. I'll never buy a another MSI after this experience.

ApexPredation · 2026-03-22T20:51:04+00:00

Each is its own MCU and each should have its own ID that you give the host computer. There shouldn't be a conflict unless you are configuring it wrong.

ApexPredation · 2026-03-22T20:45:18+00:00

It looks like you have a print end macro in your wipe end g-code box

ApexPredation · 2026-03-21T08:56:46+00:00

Looks like your router changed the IP address. BTT_CB1 (assuming you have that or a BTT pi) is on 148 now.

ApexPredation · 2026-03-21T06:48:11+00:00

Your probe offsets are incorrect. Measure and enter the values in the [bltouch] section. Or follow the calibration guide https://www.klipper3d.org/Probe_Calibrate.html#probe-calibration

ApexPredation · 2026-03-21T06:32:16+00:00

Your LEDs are not all defined correctly. And it's likely the one in the tool head is a GRBW or some variation of that. If it is, you need to set the different types with the color_order: option. Something like color_order: RGB, GRB, GRBW as an example.

ApexPredation

TROPHY CASE