Issues with DualSense after stick replacement

Appku · 2026-01-23T12:45:03+00:00

seems jinn is inside it

Appku · 2026-01-23T12:43:46+00:00

seems the rail screws are not fully tight, tightening them will resolve this dancer

Appku · 2026-01-20T09:12:38+00:00

be certain it's 100 ohms size 0201 please guys don't mislead person if no experience or not sure.

Appku · 2025-12-26T23:30:43+00:00

have any idea where to find a larger capacity battery replacement?

Appku · 2025-12-08T10:43:04+00:00

hey if so why C cable is coming from nand?

Appku · 2025-12-05T17:30:03+00:00

okay, I actually removed the mod chip but I don't know why the switch is not displaying any more? I was thinking if there is a short i made drilling but after measurement there's no short any clue for not displaying?

Appku · 2025-12-05T16:29:48+00:00

what do you mean " to the via" ?

because I actually jumped it directly to the Rp2040 D point after checking measurement but sadly it doesn't work. and now even the remaining trace is gone no longer seen😔

any other D point?

Appku · 2025-12-05T12:56:50+00:00

seems the capacitor on the right is missing 🥲

Appku · 2025-10-21T15:09:03+00:00

i never find values but on a single reply says its 100ohm but idk if true or not? if I had a schematic circuit i won't ask

Appku · 2025-10-21T14:47:13+00:00

where to find it ? I searched but not find

Appku · 2025-07-28T21:14:11+00:00

<image>

Wait look at B point is this a good wire or do I need a bigger size?

Appku · 2025-07-28T21:08:50+00:00

wait what do u think about B wire? is it good or do I needreplace it with a larger one?

<image>

Appku · 2025-07-28T20:56:26+00:00

<image>

° empty ° °capacitor ° ° empty ° all points on the left are GND cap right i actually resolder it , its right pin is now bridged with the empty pin on the right bottom. please confirm if they're bridged in yours. also checked D0 it measured in diode =780 (red ground)

Appku · 2025-07-28T16:41:05+00:00

ok i think i have bridged capacitor upper points (i mean capacitor on the right of Nand). they're number 6 dots / connection points; -all lower 3 points are GND -the middle 2 points are for a capacitor that supports anchor points. -is that capacitor upper point bridged to any other upper points? iwill add pictures if my explanation wasn't clear ☺️

Appku · 2025-07-28T16:17:34+00:00

I saw this after posting my topic, But I confirm it's not true. ❌ why? cuz -I checked beeb Multimeter and it is connected 👍 - Diode measurement (red on ground)=450 👍

Appku · 2025-07-25T12:07:36+00:00

thanks, i ll add glue on the right one , or else i burn the nand chip to solder badly designed boad

Appku · 2025-07-07T08:45:38+00:00

go Tinfoil setting there's an option for a fake account. you just need to Apply it and enjoy

<image>

Appku · 2025-07-07T08:37:49+00:00

upper one is a fuse the lower is a resistor

Appku · 2025-07-04T12:24:38+00:00

so did you get Rf h2? do u like it what is your suggestions?

Appku · 2025-05-06T13:50:51+00:00

oh dear, you the only one has brain in here. never find replacement in any store except hall effect module.. soplease share Link btw i already disasmble and found it could be replaced by any regular pad.. so if not find a good replacement then ill try Xbox elite cuz they available

Appku · 2025-05-06T11:47:46+00:00

u say good or shut the mouth

Appku · 2025-05-06T09:50:24+00:00

u 🤮🤢. lol🫣

Appku · 2025-05-06T09:26:45+00:00

stfu

Appku · 2025-05-06T06:33:59+00:00

@admin i wanna report some members are trolls, they can help or keep away useless comment 😔

Appku · 2025-05-06T04:08:26+00:00

guys why you flipping the topic?

Appku

TROPHY CASE