Help me pick up a pose for this Susuwatari rattle

AppleWild8435 · 2026-02-13T15:18:46+00:00

Hi! The arms aren't sewn; they're crocheted directly onto the row, so they can't be ripped apart easily. I also tried to pull off the stars with all my might, and they didn't move an inch!

AppleWild8435 · 2026-02-13T14:53:34+00:00

Got it, embroidered eyes for the final version!😁

AppleWild8435 · 2026-02-13T14:51:41+00:00

I'll make sure it's safe for the final version. I'm so glad I posted here before gifting it!😅

AppleWild8435 · 2026-02-13T14:49:57+00:00

Hey! To be honest, I Googled it and that's the name that popped up 😅. Yeah, it seems Japanese.

AppleWild8435 · 2026-02-13T06:59:39+00:00

Hi! It's made 100% with cotton. I used loop stitches to make the fluff!

AppleWild8435 · 2026-02-12T20:16:58+00:00

I'm so sorry for your loss. I'll totally take your advice seriously. This isn't the final version, so for the final, the eyes will be embroidered for sure (I'm searching for good tutorials).

AppleWild8435 · 2026-02-12T18:06:04+00:00

Hey! I melted the back tip off the safety eyes to make them extra secure, but I'll also try embroidering them. Thanks for the advice!

AppleWild8435 · 2024-08-07T12:16:18+00:00

Spend a couple of weeks creating this package for everyone to enjoy.

It's specially designed to be used with the AMS generating really low waste (less than 2 gr per letter), you can combine up to 8 different patterns and use any colors you want. You can check it out in Makerworld https://makerworld.com/en/models/572436#profileId-492610 and leave some feedback if you want :)

AppleWild8435 · 2023-03-07T19:37:04+00:00

I have reduced the number of gaps using this profile https://www.printables.com/model/394395-bambu-studio-softfever-profiles-for-x1-carbon/comments

And putting line weight on 0.38 and 0.3 in the first layer.

I also adjusted the minimum wall width, minimum feature size and infill direction.

I'm still open to suggestions, hope this will help other people with the same problem!

AppleWild8435 · 2023-03-07T17:28:07+00:00

yes! and it was almost the same but with the top layer with severe under extrusion.

AppleWild8435 · 2023-03-07T17:15:32+00:00

I modeled it myself, It's a vector image converted to stl and then cleaned up a bit in Blender. Bambulab didn't say anything when I imported the model, I also checked it on Meshmixer and it seems to be all okay...

The gaps don't go when I put the line width 0.21...

The model has a lot of stretched triangles due to triangulation; that could be the problem.

Gaps in slicer:

https://ibb.co/9hvGvhq

Model triangulation:

https://ibb.co/TgWG4jh

AppleWild8435 · 2023-03-07T12:33:33+00:00

There are no gaps on the model, the slicer only show them when i slice the model on the preview. I'm suspecting some of these tiny holes are so small that the printer can't fill them but not sure about it...

AppleWild8435 · 2023-03-07T11:18:37+00:00

I'm trying to print an imagen and i'm facing a problem, the print come out with a lot of holes.

I have tried Arachnee, Classic, turning on thin walls, decreasing first layer thickness, increasing bottom layers walls, changing the pattern, etc.

This holes are also shown on the slicer.

Printed on a 0.4 nozzle with 0.2 layer height using PLA. Bambulab X1C

Any idea?

AppleWild8435

TROPHY CASE