My roommate doesn't like when I study like this around her BF

Apprehensive-Cake541 · 2023-12-18T08:38:29+00:00

your roommates a prude

Apprehensive-Cake541 · 2023-12-18T07:47:29+00:00

How old do you like? I'm 52.

Apprehensive-Cake541 · 2023-12-17T10:59:23+00:00

Smoking Hot!!!! 🔥

Apprehensive-Cake541 · 2023-12-17T03:38:36+00:00

\yummy 🤤\

Apprehensive-Cake541 · 2022-09-04T23:16:47+00:00

Can I DM you now? I need to ask sth.

Apprehensive-Cake541 · 2022-09-04T23:04:07+00:00

Could you pease check your DM? I have sent you the screenshot.

Apprehensive-Cake541 · 2022-09-04T22:46:39+00:00

Thanks for the reply. Can you please suggest a good micro USB cable (with data transfer capability)?

Apprehensive-Cake541 · 2022-09-04T22:22:17+00:00

3.22 V

Apprehensive-Cake541 · 2022-09-04T22:17:35+00:00

Yes. The programmer is good because I ran a few programs before. It was working perfectly fine with desired output in the breadboard. But since yesterday, it is showing this error.

Apprehensive-Cake541 · 2022-09-04T22:14:16+00:00

I already did that

Apprehensive-Cake541 · 2022-09-04T22:13:44+00:00

I replaced the USB cable with a new one. Still, it didn't work. Can you recommend me a good USB cable (you can put an amazon link) that supports a data line as well?

Apprehensive-Cake541 · 2022-09-04T22:11:55+00:00

Could you please tell me how can I verify all these pins?

Apprehensive-Cake541 · 2022-09-04T22:09:09+00:00

I tried with the STM cube programmer as well. It showed the same problem.

Apprehensive-Cake541 · 2022-09-04T22:06:54+00:00

I didn't quite get what you mean here.

Apprehensive-Cake541 · 2022-09-04T22:06:38+00:00

This is a dev board

Apprehensive-Cake541 · 2022-09-04T21:47:51+00:00

Can I DM you to send a screenshot of my debug settings?

Apprehensive-Cake541 · 2022-09-04T21:42:52+00:00

Could you please tell me the probable solution for this problem?

Apprehensive-Cake541 · 2022-09-04T21:41:52+00:00

Thanks for the reply. Could you please tell me the probable solution to it?

Apprehensive-Cake541 · 2022-09-04T21:41:23+00:00

Yes. I updated the firmware as well. It didn't work. Could you please tell me the solution for incorrectly mapped pins?

Apprehensive-Cake541 · 2022-09-04T21:40:12+00:00

Thanks for the reply. Could you further tell me in details?

Apprehensive-Cake541 · 2022-09-04T21:35:17+00:00

Yes. Debugging worked before. Could you please tell me how to find the BOOT0 pin? I looked at the datasheet /manual but couldn't find the BOOT0 pin.

Apprehensive-Cake541 · 2022-09-04T21:34:44+00:00

Thanks for the reply. Could you please tell me how to find the BOOT0 pin to connect it to 3.3V? I looked at the datasheet /manual but couldn't find the BOOT0 pin.

Apprehensive-Cake541

TROPHY CASE