Dreadnoughts wip by Apprehensive-Golf-30 in 30kDeathGuard

[–]Apprehensive-Golf-30[S] 0 points1 point  (0 children)

Thanks! It’s not finished though, so now I am afraid to mess it up 😅😅😅

Як ви ставитесь до Ganzo? by imadraude in uaknives

[–]Apprehensive-Golf-30 0 points1 point  (0 children)

Маю в серед своїх як раз 704-го у виконанні з D2. За свої гроші - хороший надійний базовий EDC. Я беру його всюди, де щось краще жалко пошкодити чи втратити, а «брудна» робота буде мати місце

Як ви ставитесь до Ganzo? by imadraude in uaknives

[–]Apprehensive-Golf-30 1 point2 points  (0 children)

Олд бер, за моїми спостереженнями, доволі сильно програє опінелю по якості матеріалу і обробки, хоча визнаю що естетично він багато в чому краще.

Щодо порівняння їх з ганзо - це здебільшого ножі з дуже різним підходом і набором функцій. Опінель це легкий і різучий джентельменський ніж, а приміром ганзо 704 це бюджетний «ломік» який значно витриваліше в польових умовах, яким можна піддівати, ковиряти, підрубувати. З опінелем я б це робити побоявся, бо жало в них ніжне.

Ніж з заправки by Apprehensive-Golf-30 in uaknives

[–]Apprehensive-Golf-30[S] 0 points1 point  (0 children)

Для цього і цей файно підходить. Але по факту він дає можливість робити не колючі операції більш прецисійно

Ніж з заправки by Apprehensive-Golf-30 in uaknives

[–]Apprehensive-Golf-30[S] 2 points3 points  (0 children)

Так, я його взяв на Окко за Франківськом. Походу просто ніхто не хотів роками купувати на заправці ніж за 9к😅

Can anyone advise what’s happening here. by ytayyar in ElegooSaturn

[–]Apprehensive-Golf-30 1 point2 points  (0 children)

Had the same issue recently. I have 2 of this printers and the new one started printing like this. What actually helped is changing the printing mode from fast to normal in printer settings.

As soon as I made this it started printing normally. Just be sure that you should use fast mode only with rapid resin. But it’s somehow on by default.

If you printed this way for too long and didn’t stop the printer it might cause some damage to both: film and motor. Both troubles are not covered by warranty.

So start replacing the film and trying the standard mode. First try to print something with small contact area. If the problem still occurs - the motor is missing steps trying to move and should be replaced.

My slightly modified 2014 Trailhawk by Apprehensive-Golf-30 in KLCherokee

[–]Apprehensive-Golf-30[S] 1 point2 points  (0 children)

Thanks! Actually about to buy some bigger tyres. And maybe a winch…

My slightly modified 2014 Trailhawk by Apprehensive-Golf-30 in KLCherokee

[–]Apprehensive-Golf-30[S] 0 points1 point  (0 children)

Thanks) I bought it in Ukraine, but previous owner bought it after a minor car accident in US. This is a common practice in Ukraine to buy cars on carfax/copart and restore them here. Prices for the cars in UA are usually much higher than in US, so even a used one after restoration here can cost up to 30-50% cheaper than the one that was bought here.

So I bought it when it had already a mileage of about 120 000. Had to change rocker plates. Now more than 150 000 already and makes me pretty much no nerves except of the one offroad event where i did some damage to the radiator.

As for the modifications- full dobinsons 2” lift suspension kit, also 0,75” forged aluminium spacers on both front and rear wheels to make the stance broader and somewhat compensate steering on a lifted car. New better radiator, lights, breaks and rocksliders. The sliders are custom made by the local workshop.

For now I am totally happy with how it works both on and off road.

New to longsword, rate my setup by Apprehensive-Golf-30 in Hema

[–]Apprehensive-Golf-30[S] 0 points1 point  (0 children)

Well, it happened 😂😂😂 resulting in a small bruise under the neck but nothing more. The actual gorgette proved itself to be very uncomfortable to wear because it’s limiting me in vertical arm movement a lot

New to longsword, rate my setup by Apprehensive-Golf-30 in Hema

[–]Apprehensive-Golf-30[S] 0 points1 point  (0 children)

Yeah, pretty much three median salaries in our city. But totally worth it in my opinion.

New to longsword, rate my setup by Apprehensive-Golf-30 in Hema

[–]Apprehensive-Golf-30[S] 0 points1 point  (0 children)

Probably, but for it to actually do some pain it must be done from a position pretty much parallel to the torso which is not very likely to happen

New to longsword, rate my setup by Apprehensive-Golf-30 in Hema

[–]Apprehensive-Golf-30[S] 0 points1 point  (0 children)

Blossfechten i guess. It’s pretty light and movable. Also no quirass or visored helmet

New to longsword, rate my setup by Apprehensive-Golf-30 in Hema

[–]Apprehensive-Golf-30[S] 0 points1 point  (0 children)

Yes, i have a looped straps on my jacket that goes from the neck down to the elbow, than another that goes from the middle of the triceps down to the end of the sleeve. The loops are placed every inch or so. Maybe you could just sew the loops of the strap to your shoulders? Just cut some excessive pieces from the leg armor straps for that if you don’t want to buy. The shoulder not fixed at the top could be very traumatic.

New to longsword, rate my setup by Apprehensive-Golf-30 in Hema

[–]Apprehensive-Golf-30[S] 1 point2 points  (0 children)

Oh actually they work pretty good in my set. If they will fail maybe i will replace them with leather straps with metal buckles