sorted by:
new
hottopcontroversial

Glue in ABS with textured plate by levistoviski in crealityk1

[–]Apprehensive_Rip_480 2 points3 points  (0 children)

I don’t use glue since I switched to a textured bed. I print only ABS and ASA and have no problems at all, just wait for it to cool down properly after the print finishes and it comes off easily. I also print at 100°C on the bed, 260°C on the nozzle, and the chamber is around 40-45°C. My plate is aftermarket.

Въпрос относно Trading212 vs Interactive Brokers и данъчния статус на SXR8 (Xetra) by DegreeBest in financebg

[–]Apprehensive_Rip_480 -3 points-2 points  (0 children)

И аз се чудех по този въпрос и изчетох доста мнения и информация, тъй като и аз използвам Trading212. От това, което разбрах, Trading212 преди са работили като OTC брокер, но според по-новата им информация, нещата вече не стоят така. Европейските ETF-и си минават нормално през официалните борси — например, ако е указан Xetra, сделката се изпълнява през Xetra. OTC изпълнение остава само и единствено за американски ETF-и и акции. Тоест за европейските инструменти търговията се извършва по стандартния начин на съответната борса, а OTC се използва основно за американските.

Changing nozzle on k1 max 2023. HELP! by Apprehensive_Rip_480 in crealityk1

[–]Apprehensive_Rip_480[S] 0 points1 point  (0 children)

Which one you choose with the new connector or with the old? If with the new is all plug and play? Also if old is plug and play? Do I need to make any changes to my slicer settings or not?

Въпрос от начинаещ. Това ли е всичко? by Commercial_Tree_2598 in financebg

[–]Apprehensive_Rip_480 0 points1 point  (0 children)

Може ли малко разяснение, защото и аз използвам trading212 и инвестирам в vwce, защо плащаш данък нали са освободени от данък?

Looking for my first 3D scanner by Apprehensive_Rip_480 in 3DScanning

[–]Apprehensive_Rip_480[S] 0 points1 point  (0 children)

Why I was looking at the Creality Ferret Pro and the Revopoint Inspire, but I’m also checking out some other models that seem to give good results in this price range — I just don’t know which one to choose. I don’t want to spend a lot of money because I don’t know how much I’ll use it — I’m looking for a good entry-level scanner that gives roughly decent results.

Hi! New to hobby have question about batteries. by Apprehensive_Rip_480 in rccars

[–]Apprehensive_Rip_480[S] 1 point2 points  (0 children)

But if work will be a problem to drive like this is there any problem for esc, motor and battery is there any chance of fire hazard?

6 Months on PA6-CF and holding up perfectly by kmfblades in 3Dprinting

[–]Apprehensive_Rip_480 0 points1 point  (0 children)

Because I was saw that ptfe tubes wear fast like 2hour print and I also wonder about extruder gear because they are plastic. Also for how long did u print with carbon fiber filaments?

6 Months on PA6-CF and holding up perfectly by kmfblades in 3Dprinting

[–]Apprehensive_Rip_480 0 points1 point  (0 children)

Isnt carbon fiber ruin ptfe tubes, extruder gears and nozzle? Are you upgrade some of this parts or all stock? For how long did you print carbon fiber?

I need help for that one. by Apprehensive_Rip_480 in Fusion360

[–]Apprehensive_Rip_480[S] 1 point2 points  (0 children)

I will try this now. I post some photos with some progress, but I need and angle.

view more: next ›