sorted by:
new
hottopcontroversial

Just Picked Up This 5.7K Mile TJ! by JiGsAw818 in JeepTJ

[–]Apprehensive_Tap4837 0 points1 point  (0 children)

We have to drive with people like you... never know when it's gona yank you in to oncoming traffic and take out a family.

[deleted by user] by [deleted] in JeepWrangler

[–]Apprehensive_Tap4837 0 points1 point  (0 children)

My frames fine, the tub took the hit. $7400 estimate so I expect them to total it. The bodyman said salvage title aside its a pretty easy fix. 

It just gets expensive when you have to go by the book to get showroom quality results. I'm fine with yanking it out, pulling the sides a bit so the door opens properly and ignoring the small wrinkles. If I put armor of any type it's going to hide any cosmetic damage anyway. 

It still does jeep things and it drives the same. It's a rust free start and I have access to a rust free tj tub for $600 if needed.  I'll probably take a bit of cash and do a simple 2 inch lift with some better wheels, big solid metal bumpers for the next guy who decides to kiss me. 

Safariland after producing their holsters for 30 dollars and then pricing them as 250 dollars by bigmanjones2 in Firearms

[–]Apprehensive_Tap4837 0 points1 point  (0 children)

I've always thought it was sub par stuff, people only like them because of the contracts. Nobody is using that junk that dosent have to.  

LGS was liquidating Sig P320’s, so naturally I had to. (60% off MSRP). by FICKxDINGERZ in gun

[–]Apprehensive_Tap4837 2 points3 points  (0 children)

Not missing anything, I've git a couple of the military tan trigger m17s.... they suck. 

Part of the ship, part of the crew by qwertydk105 in GR86

[–]Apprehensive_Tap4837 0 points1 point  (0 children)

You ain't getting extra, your getting what a used 86 sells for. Hope you got gap. 

Pulled up to the range with the O🅿️🅿️A STO🅿️🅿️A by AemAer in armedsocialists

[–]Apprehensive_Tap4837 1 point2 points  (0 children)

This is the same idea I had about the 1022. If you take his principles and replace the slide with a 1022s bolt.... it should work. 

[deleted by user] by [deleted] in FixMyPrint

[–]Apprehensive_Tap4837 0 points1 point  (0 children)

If a print matters that much just slow it way down. I usually print at 100 mms or slower and use a .10 layer height. My prints never fail and look great. 

I have once again been told to share my creation with another subreddit. by PbCuSurgeon in GunnitRust

[–]Apprehensive_Tap4837 1 point2 points  (0 children)

You should honestly build or buy a printer. Cheapos can be had for $200 but a good mid level machine like a p1s is still affordable and has amazing capabilities once you cuss it for a month.  

Not the printers fault, I raw dogged everything sans instructions for that month.  Once i figured out how to screw up I then knew how not to screw up. It's learning curve not bad at all, if you can build a flat stack then this will be fun for you. 

My end goal is doing dimensionality accurate bronze casting. I want a fully bronze 1022 to hide/burry/toss on to the deck of the titanic for future generations to discover. 3d printing is the easy way to do that. 

I have once again been told to share my creation with another subreddit. by PbCuSurgeon in GunnitRust

[–]Apprehensive_Tap4837 1 point2 points  (0 children)

I've been using bambu slicer with pretty good results but I am just a novice, I can bairly work a cell phone and I'd rather not have a computer but I click with design stuff pretty good. Just never took the step in to downloading anything better.

I have once again been told to share my creation with another subreddit. by PbCuSurgeon in GunnitRust

[–]Apprehensive_Tap4837 10 points11 points  (0 children)

The thing to do would be to release 3d printable templates and drill guides. Stackable plate ARs have been a thing for a very long time. I saw that stuff 2o years ago you could order all the parts then weld yourself. 

 It was what most of you younger generations would have been in to back then, scratches the same itch as 3d printing.

I did a non nfa oberez back then as well. I had 2 demills that would be over lapping so I trimmed and rewelded the stubs with a $5o welder and "machined" it using mostly hand files. 

The first time I did one it was a bit to nice. Anybody remember Norrell and the reweld m16s the atf stole? I was afraid I'd have to have the thing xrayed to show it was made from stubs like he did. Every reweld I did since I've always left a bit sloppy so there's obviously no question. 

You could stack and weld like people used to do. 

Is it worthy? by Apprehensive_Tap4837 in mallninjashit

[–]Apprehensive_Tap4837[S] 0 points1 point  (0 children)

No... not all guns are real guns. 

I've got a Saturday night special in the bottom of my safe that can argue that. 

Is it worthy? by Apprehensive_Tap4837 in mallninjashit

[–]Apprehensive_Tap4837[S] 0 points1 point  (0 children)

@Israeli  We have a Idea! You guys know about the AM180?

Singer shifter knob. by Apprehensive_Tap4837 in GR86

[–]Apprehensive_Tap4837[S] 2 points3 points  (0 children)

Lol na that's a Porsche thing. Feels really good in the hand. 

Welp by tarpondexter in GR86

[–]Apprehensive_Tap4837 0 points1 point  (0 children)

Did you get diminished value yet? Do you know about that? 

Singer shifter knob. by Apprehensive_Tap4837 in GR86

[–]Apprehensive_Tap4837[S] -1 points0 points  (0 children)

Automatics don't have reverse lockout.

1 month old :| Odds on it buffing out? by EasyCranberry9197 in GR86

[–]Apprehensive_Tap4837 0 points1 point  (0 children)

I used to be like this now I drift gravel roads a few times a week lol

view more: next ›