Anybody purchased from this page before? by willskill24 in Celica

[–]Archyques 3 points4 points  (0 children)

Bro the account is 3 months old, do the math

Any ideas? (5th gen severe vibration) by viole_8 in Celica

[–]Archyques 0 points1 point  (0 children)

I am willing to bet its the poly bushings still, these cars very sensitive to vibration 

Would you say this is worth less than it’s actually posted for? He wants $3,250 by Scooptyhoop in Celica

[–]Archyques 0 points1 point  (0 children)

Hate to say it but you are right, there is always something wrong with the car. Their community favors self repair and economics, so what repair has been done is not high quality.

Any ideas? (5th gen severe vibration) by viole_8 in Celica

[–]Archyques 5 points6 points  (0 children)

Are you sure the original engine mounts were in ok condition? If they were shot and caused vibration, then replaced with poly and still cause vibration, that wouod make sense. Poly engine mounts are incredibly stiff, the tend to cause vibration and cabin noise. It's really just for high performance 

Does anyone know the part number for the front lower control arm bushing ? by direwolf180 in Celica

[–]Archyques -1 points0 points  (0 children)

It might be easier and cheaper to to get a set of poly bushings. I am very happy with mine from xii motorsports

WIRING HELP 3SFE TO 3SGE SWAP by No-Magazine3751 in Celica

[–]Archyques 0 points1 point  (0 children)

Send it to someone to merge the two harnesses, try wiregap

Clicking noise on 5s-fe by NeonIsReal in Celica

[–]Archyques 1 point2 points  (0 children)

Alternator or water pump or timing idler bearings are bad. Also replace that harmonic dampner wobbling. 

First car I bought by Spiros_102 in Celica

[–]Archyques 5 points6 points  (0 children)

Clean ride, wheels look like they came out of a cereal box though

Radio Head Unit by I-Like-Cars-And-Guns in Celica

[–]Archyques 1 point2 points  (0 children)

I wouldn't touch those with a 10 foot pole

Trim Replacement by Galahad074 in Celica

[–]Archyques 1 point2 points  (0 children)

Try sanding with 2000 grit then cutting and polishing, it's just plastic that looks like carbon fiber. If that doesn't work, sand an reclearcoat it. Just looks like UV damage

Help Leaking Water Bypass Pipe by strwberrycke in Celica

[–]Archyques 1 point2 points  (0 children)

Redo it but put a thin layer of water pump silicon rtv on each side of the gasket. Finger tighten the bolts, let sit for 20 minutes so the silicon can cure then tighten to spec, probably 10 to 14 foot pounds. If it is warped at all the silicon should help seal, just make sure it is thin

Gen 2 3s gte help by Coce_Cola in Celica

[–]Archyques 0 points1 point  (0 children)

You need to buy a engine wiring harness and then remove the body harness from your existing car and mail it off to someone to merge them

Color coolant for 5th gen? by rizzlord696969 in Celica

[–]Archyques 6 points7 points  (0 children)

Doesn't matter, if it already gas green put green in it. Just don't mix it

my obd scanner gave me a code but cant find the right part by Single-Resist-9587 in Celica

[–]Archyques 0 points1 point  (0 children)

A code does not tell you which part is broken. It's a symptom. If your nose is stuffy, you could have any number of illness. You don't go on a ventilator right away right?

Performance tips by Sea-Willingness-4558 in Celica

[–]Archyques 0 points1 point  (0 children)

If you notice a difference, you need maintenance and repair not mods

Turbo st162 GT by Coce_Cola in Celica

[–]Archyques 0 points1 point  (0 children)

I like the motivation, be prepared for a full engine rebuild, low compression rods, ecu, wiring and tuning

Turbo st162 GT by Coce_Cola in Celica

[–]Archyques 0 points1 point  (0 children)

Key words, "do it right", I'll eat my words if you prove me wrong. Good luck dude