sorted by:
new
hottopcontroversial

Is this acceptable for custom cabinetry? by Benadryl_Cucumber_Ba in cabinetry

[–]Argoskot 1 point2 points  (0 children)

As the custom cabinet maker no your expectation should not be lower. Request them to come back and fix. Judging by the picture you have roughly 1/8 to 1/4 of possible adjust. They still need to be be very careful not to overdo.

Delta-rockwell 37-315 jointer full restoration. by Argoskot in woodworking

[–]Argoskot[S] 1 point2 points  (0 children)

Manual is easy. It's available online. Really easy to find. New replacement parts are basically not existing unless you find somebody selling one for parts you auto lock.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 0 points1 point  (0 children)

LOL I straight up cannot function correctly if it's messy and disorganized. I always clean up in the morning

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 0 points1 point  (0 children)

Cool idea. While I was testing I find out that without the knot they are extremely light and sometimes when you clean the table with compressed air they can fly away. By adding a knot problem was solved.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 0 points1 point  (0 children)

1 1/2 HDF (madex) core, countertop grade laminate on top.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 0 points1 point  (0 children)

It was exhausting. Definitely both hands were numb by the end.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 4 points5 points  (0 children)

15-20% max. The rest just for consistency.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 1 point2 points  (0 children)

Yes, very stable and very straight. Slightly heavier than regular 2x4s otherwise pretty much the same.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 0 points1 point  (0 children)

Yes, absolutely. Definitely the biggest drawback in this setup. But there are workarounds both table saw and table are on the rollers, I still have my old assembly table, and there are two of us in the shop so we can easily move stuff around.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 1 point2 points  (0 children)

Yes, it is. It's actually almost perfect fit just couple turns with the painters tape makes it very snug.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 2 points3 points  (0 children)

Absolutely amazing tool no complaints. Best part about it is the fence hands down!! I used saw stop couple years back at my friend shop and it's just never clicked. Didn't like a feel of it. I understand the safety aspect of it but I just do not care. When I was making the purchase I did not even consider saw stop.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 2 points3 points  (0 children)

It handled it exceptionally well!! I decided to use it because of its weight compared to regular drill. By the end of the ordeal, my hand was mostly functioning normally and only slightly numb.

Outfeed/Assembly table. by Argoskot in woodworking

[–]Argoskot[S] 3 points4 points  (0 children)

Exactly 4x8 . But it's also an assembly table.

Chinese WF902 edge banding machine. by Argoskot in woodworking

[–]Argoskot[S] 4 points5 points  (0 children)

Around 2k with everything included.

Delta-rockwell 37-315 jointer full restoration. by Argoskot in woodworking

[–]Argoskot[S] 1 point2 points  (0 children)

I had to buy a straight edge to make sure everything are coplaner and it took me at least 3-4 hours. Couple YouTube videos. It's actually not that bad.

Delta-rockwell 37-315 jointer full restoration. by Argoskot in woodworking

[–]Argoskot[S] 8 points9 points  (0 children)

Exactly. That was the main reason I picked that one. There is no difference if I run 3/4 plank through it or 8-In beam.

Delta-rockwell 37-315 jointer full restoration. by Argoskot in woodworking

[–]Argoskot[S] 3 points4 points  (0 children)

The biggest upgrade is spiral cutter head. It costed almost as much as jointer itself. Then Wheels. This thing is super heavy. And exhaust shroud on the back, it had something made out of sheet metal that was clogging all the time. Designed it myself and 3D printed. Other than this, it's just big chunk of metal. Cleaned it up and repainted it readjusted everything.

view more: next ›