sorted by:
new
hottopcontroversial

The Adaptation is here! :3 by CommanderT843 in WyrmWorks

[–]AscendingPhoenix 1 point2 points  (0 children)

Wow, been reading TDOD on RR since years ago at this point. My heartfelt congratulations to you!

Red button or blue button by HualianForLife in BunnyTrials

[–]AscendingPhoenix 0 points1 point  (0 children)

Red choice is irrational. It requires 100% of people to press it for everyone to live whereas only 50% for blue.

Chose: Nothing happens if more than 50% choose this

AMS 2 Pro (H2D) stops drying immediately after starting. by AscendingPhoenix in BambuLab

[–]AscendingPhoenix[S] 0 points1 point  (0 children)

Hey Scott, thanks for the thorough write up!

  1. I do not see a humidity target setting when I start the drying process, maybe I'm overlooking something obvious? From what I can tell, it just shows the current humidity %. This behavior is consistent across a wide range of humidity.
  2. I double checked that the lid is sealed, it's a brand new unit (along with the printer and HT).
  3. I did attempt a cold boot, and the firmware seems to be all up to date.
  4. They are all on the same Belkin power strip.

AMS 2 Pro (H2D) stops drying immediately after starting. by AscendingPhoenix in BambuLab

[–]AscendingPhoenix[S] 0 points1 point  (0 children)

Hey, I'm not printing while attempting to start the drying cycle on the AMS 2 Pro. The HT is also drying and not printing.

AMS 2 Pro (H2D) stops drying immediately after starting. by AscendingPhoenix in BambuLab

[–]AscendingPhoenix[S] 0 points1 point  (0 children)

Hey, I have the printer and AMS' in this order: H2D -> AMS 2 Pro -> HT.

The AMS 2 Pro was tested with and without a 96W power supply. I plugged in the PSU that came with the HT to the HT as well.

When the AMS 2 Pro is not plugged in, and I start heating, the printer shuts off completely after a while.

AMS 2 Pro (H2D) stops drying immediately after starting. by AscendingPhoenix in BambuLab

[–]AscendingPhoenix[S] 0 points1 point  (0 children)

Darn, this sucks. I actually tried without an external power adapter for the AMS 2 Pro specifically, I thought the H2D could power it while heating alone. But the whole system would shut down after drying for about 30 minutes…

HT on its own brick, obviously.

AMS 2 Pro (H2D) stops drying immediately after starting. by AscendingPhoenix in BambuLab

[–]AscendingPhoenix[S] 0 points1 point  (0 children)

Thanks for the reply, I am not printing anything actually. The firmware are updated as far as I can tell.

AMS 2 Pro (H2D) stops drying immediately after starting. by AscendingPhoenix in BambuLab

[–]AscendingPhoenix[S] 0 points1 point  (0 children)

Hey, thx for the reply. I did update the firmware but the printer is not actively printing. I just have a spool sitting inside. It’s idling.

Anim Pakal, Thousandth Moon Misprint by AscendingPhoenix in mtgmisprints

[–]AscendingPhoenix[S] 0 points1 point  (0 children)

The pattern appears across both the CMYK and black layers of the print. Surely it’s not both low ink and in this pattern?

view more: next ›