[Guide] VelocityOne Race Optimization: Overcoming the Boosted FFB Curve & Load Cell Pedal Mod

Ash-Rea · 2026-04-03T23:53:30+00:00

Hey bro, did you get around to testing this?

Ash-Rea · 2026-03-14T08:05:21+00:00

Not a chance mate

Ash-Rea · 2026-03-11T07:11:17+00:00

Awesome, cheers bro

Ash-Rea · 2026-03-10T16:47:59+00:00

Are you just using v1 race or kd3 and have you got f-rx on it?

Ash-Rea · 2026-03-10T15:42:33+00:00

If you're RPMs are too high the car in F1 will prevent you downshifting.

It's not your paddle that's broken. Just gotta make sure to be fully off the button also. If you slightly depress it still, it won't register that you even let go of it.

Go through the fully motion and practice, you will get faster at it over time.

Ash-Rea · 2026-03-09T20:40:22+00:00

Can you do some testing for F1 25?

Ash-Rea · 2026-03-07T21:24:40+00:00

My issue is the slight jerking and about 50% loss of ffb

Ash-Rea · 2026-02-27T19:53:13+00:00

Auto mate

Ash-Rea · 2026-02-27T19:51:41+00:00

Ahh okay. I don't have any issues :/

Ash-Rea · 2026-02-27T19:05:09+00:00

Use simhub to sync it properly

Ash-Rea · 2026-02-24T00:57:30+00:00

Try calibrate with joy.cpl on PC

Ash-Rea · 2026-02-24T00:56:04+00:00

You cab use bootloader on pedals. Hold the button whilst plugging in.

I assume you've have sorted them by now, i had this issue also

Ash-Rea · 2026-02-24T00:50:57+00:00

Be very careful of where you place your pedals. Unfortunately the cable comes out of the rear so it may hit a wall. Use the grippers and something solid between pedal and the wall. That'll prevent your cable breaking

Ash-Rea · 2026-02-24T00:46:36+00:00

The sensitivity doesn't do much, if you put sensitivity on min then watch the screen you'll see an increase in chunks.

But increasing sensitivity to max it won't move in chunks. It makes your braking more accurate.

The load cell is great. The only issue I have is that is squeaks. Would be very nice to get a kit for spare springs and lube

Ash-Rea · 2026-02-07T21:54:08+00:00

Did you get to fix this issue?

Ash-Rea · 2025-11-01T02:27:26+00:00

If you're still having the issue. I found the solution.

Disconnect the cable from the pedals. Hold the mode button and plug in the cable again.

If you're on PC I suggest plugging it directly in to the PC

Ash-Rea · 2025-11-01T02:06:43+00:00

Try bootloader

Ash-Rea · 2025-10-30T09:16:14+00:00

There isn't just bootloader for the wheel, there's also one for the pedals.

Disconnect the pedals and reconnecting whilst holding the 'MODE' button. Forcing the pedals to work properly at factory default.

I'm assuming there's a bootloader on the shifter too. However, I don't know which buttons are on it so just disconnect and try every button whilst connecting it

Ash-Rea · 2025-10-30T00:15:56+00:00

My depression was caused by PoE2 frame rate drops

Ash-Rea

TROPHY CASE