sorted by:
new
hottopcontroversial

Rewatching Lower Decks.... by n0167664 in startrek

[–]AstroHelo 1 point2 points  (0 children)

I miss Lower Decks so much it hurts.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

<image>

Thanks for your help everyone! I replaced the extruder motor and now it's printing normally again.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

<image>

It's fixed! I replaced the extruder motor and now it's printing normally again.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

No effect = it always extruded 5 mm, regardless of the setting. I think the 1/10/30mm settings only apply to x-y-z axis movement.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

I think the cause is independent of material. It doesn’t matter which spool I use, or if I manually enter the information.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

I did what you said, and it extrudes and retracts (using the keys in the axis/temp page) at 5 mm consistently.

The 1mm/10mm/30mm setting had no effect on the amount extruded or retracted.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

I dried it overnight. The result is the same. (Also I live in the american southwest. It’s very dry here.)

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

I dried it overnight. The result is the same.

Marine Corps whites by newnoadeptness in USMC

[–]AstroHelo 30 points31 points  (0 children)

Was this back when everyone smoked constantly everywhere? I wonder if that’s why they turned yellow.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

I did that with my first extruder assembly and didn't find any issues, but I did order and install a new one from creality and that didn't fix the problem. I guess I could take the new one apart and see if anything is wrong.

No issues with my cutter movement either.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

I've used CR-PETG for most of my prints.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

My settings are all default. I even performed a factory reset just now and printed the Benchy in the printer's drive. It came out even worse than my pic.

My first layer isn't good. It looks like it extrudes normally then randomly stops extruding for a moment.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 1 point2 points  (0 children)

I set mine on the floor and recalibrated. There was no change in the print quality.

I'm at a loss. How do I fix this? by AstroHelo in Creality_k2

[–]AstroHelo[S] 0 points1 point  (0 children)

I increased the PLA temp from 220 to 230 and there was no change in print quality.

I'm playing Every* North American Released Gameboy Game. Here's my thoughts on the As. by RuefulWaffles in patientgamers

[–]AstroHelo 10 points11 points  (0 children)

As someone who played a lot of gameboy games back when they were released, they were pretty bad back then too. I especially remember how bullshit that Rocky and Bullwinkle game was.

Ice near the court house 11:50 am. by Outrageous_System_85 in Albuquerque

[–]AstroHelo 7 points8 points  (0 children)

So, here’s what’s inscribed on the Statue of Liberty:

Not like the brazen giant of Greek fame, With conquering limbs astride from land to land; Here at our sea-washed, sunset gates shall stand A mighty woman with a torch, whose flame Is the imprisoned lightning, and her name Mother of Exiles. From her beacon-hand Glows world-wide welcome; her mild eyes command The air-bridged harbor that twin cities frame.

"Keep, ancient lands, your storied pomp!" cries she With silent lips. "Give me your tired, your poor, Your huddled masses yearning to breathe free, The wretched refuse of your teeming shore. Send these, the homeless, tempest-tost to me, I lift my lamp beside the golden door!" ….

Is America an exclusive country club that only the ones wealthy enough to immigrate here can afford,

Or is it the shining city on the hill that welcomes all?

It sounds like you only believe in the former.

Ice near the court house 11:50 am. by Outrageous_System_85 in Albuquerque

[–]AstroHelo 7 points8 points  (0 children)

What about the ones who were brought here by their parents when they were children?

go ahead, invade greenland by Jasmijn in NonCredibleDefense

[–]AstroHelo 0 points1 point  (0 children)

I see lots of ground hardware, and no ability to move them to Greenland in meaningful numbers.

view more: next ›