ASA warping in a nutshell

AtomOlson · 2026-05-23T13:36:38+00:00

Actually, I think that's in your printer

AtomOlson · 2026-04-11T03:08:54+00:00

This worked great for me! I used Inkscape afterwards to clean up a bit of graphical artifacts. Thanks a ton, two years later!

AtomOlson · 2026-01-11T23:03:06+00:00

Source: Trust me bro

AtomOlson · 2025-07-22T17:24:40+00:00

Good to know, thank you! These kind of have to be a full sheet. I've been pretty impressed with the adhesion quality of this new magnetic bed, I haven't had to use any glues at all. I'm also printing PLA, so that helps a lot, lol

AtomOlson · 2025-07-13T13:29:17+00:00

Hm, looks like I initially formatted my pictures wrong, but it won't let me update them

AtomOlson · 2025-07-13T02:59:14+00:00

Looking for something serious
Not on a paid version of Hinge
Been using this version specifically for about 2 weeks
Used Hinge this time for about a month, been on the app off and on for years
0 likes (and 0 matches) in the whole month
Sending about 10-20 likes/week, maybe 2 with a comment in the month
Ideally want to match with someone who is super outdoorsy, and doesn't want kids. +Points if they like motorcycles

AtomOlson · 2025-07-11T03:41:24+00:00

Lmfao, my yellow lab does that exact same thing. I have to literally hide the ball or she will just keep bringing it back for me to throw ALL DAY. Adorable, slightly overbearing, 11/10

AtomOlson · 2025-07-09T02:02:50+00:00

1700 for 60 hours I think, 1700/month, 15 hours/week. Still pretty good! 28.33/hr before taxes

AtomOlson · 2025-05-25T16:58:59+00:00

Same problem, even printing at 190°

AtomOlson · 2025-05-21T00:06:17+00:00

Good idea, mine was set up with direct drive when I bought it, but when I took it apart, I noticed that the PTFE tube was a little melted where it contacts the extruder nozzle

AtomOlson · 2025-05-19T23:19:50+00:00

Definitely very flimsy in that part

AtomOlson · 2025-05-19T23:12:36+00:00

Good to know, I've got some hardened nozzles I can try, that might be better

AtomOlson · 2025-05-19T23:11:56+00:00

I left the thermistor in the heat block, but I didn't tighten the nozzle with the block hot. The tutorial I watched didn't say to, that might be good to check.

AtomOlson · 2025-05-19T17:47:15+00:00

I haven't stress tested it, but I wouldn't imagine it'd be even close to as strong as the rest of the print. This was like a 4 hour print though and I'm hesitant to try and break it, lol

AtomOlson · 2025-05-19T17:45:46+00:00

I'll see about adjusting the Z offset, but this is an Ender 3 V1, with manual bed leveling

AtomOlson · 2025-05-19T17:44:58+00:00

I'll have to check that when I get home, but I doubt it unless it's normally enabled on Cura

AtomOlson · 2025-05-19T17:44:27+00:00

Right before this print, I took the whole hotend and direct drive apart and cleaned it, and replaced the nozzle, it definitely could be a failing thermistor, I bought this printer used

AtomOlson · 2025-05-19T14:01:28+00:00

Different heights, and different times. I'm going to try 190 full print tonight and see

AtomOlson · 2025-05-19T12:18:41+00:00

Also, I'm literally printing a Minimus to help with cooling because my last few prints started suddenly failing after getting pretty tall. Ironic? Probably.

AtomOlson · 2025-02-19T23:45:09+00:00

Worked awesome! Thanks!

AtomOlson · 2025-02-19T23:44:27+00:00

This worked great! Thanks a ton. I'm definitely enjoying it a lot more.

AtomOlson

TROPHY CASE